Filter Results By:
Products
Applications
Manufacturers
Protective Relay
acts as a circuit breaker in the event of a fault.
-
product
Protective Relay Test Set
POM2-6143
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
-
product
Three Phase Protective Relay Test Equipment
TEST-330
Beijing GFUVE Electronics Co.,Ltd.
Test-330 three phase protective relay test equipment is a three phase current output and five phase voltage output relay tester with embedded host machine equipped with Complex Programmable Logic Device.
-
product
Protective Relay Testing Equipment
PW466i
PW466i (6×20A, 6×150V) 6-phase relay tester is a powerful secondary injection protective relay testing kit with 6-currents and 6-voltages sources.
-
product
Protective Relay Testing
Choose from Doble’s F6300e and F6350e External Amplifiers for your specific protection testing needs and requirements. These amplifiers are useful in high power protection testing applications when you need additional current and/or voltage sources, for critical high burden relay testing, as well as system modeling.
-
product
Single Phase Universal Protection Relay Test Set
S100A
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
product
Line Protection
Schweitzer Engineering Laboratories, Inc.
SEL transmission line protection relays provide subcycle line differential and multizone distance protection for a secure, reliable, and high-speed solution. Their fault-locating capabilities allow you to efficiently dispatch line crews to quickly isolate line problems and restore service faster.
-
product
Protection Testing Library
The OMICRON software technology including the OMICRON Control Center, XRIO, and LinkToXRIO enables users to create specific test templates which adapt automatically to the actual relay settings. This functionality is the technological basis of the Protection Testing Library (PTL), a comprehensive test template library for a wide range of protection relays.
-
product
FTL Test Block
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
product
Generator Protection Relay
SEL-700G
Schweitzer Engineering Laboratories, Inc.
The SEL-700G is the right solution for utility and industrial generator protection, with an autosynchronizer, flexible I/O, and advanced communications. Apply the SEL-700G for comprehensive primary and backup generator protection.
-
product
Integration
Schweitzer Engineering Laboratories, Inc.
Integrate protective relay and metering information into SCADA and plant control systems through secure networking and automation devices.
-
product
20Hz Generator
Signals & Systems India Private Limited
In order to implement a 100 % stator earth fault protection based on subharmonic injection, a 20Hz voltage is injected into the generator star point. The 20-Hz generator SGEN-1001 is used in combination with the Band Pass Filter SBPF-1001 in the Stator Earth fault protection. The injection can be performed by connecting the SGEN-1001 and the SBPF-1001 to the load resistor of an earthing or neutral transformer. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. From the driving voltage and the fault current, the protective relay determines the fault resistance.
-
product
Protection Relay Testing Equipment
S40A
S40A is a type of 3-phase protection relay test kit, with 3×40A, 3×300V, and also a local control system. It is a portable and economic secondary injection tester, and easy to use.
-
product
Relay Test Equipment
Vanguard Instruments Company, Inc.
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers. The PCI-600 is versatile and can also be used in many other applications that require a high-current source.
-
product
Protection Relay Testing
ARTES
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
product
Epoxy Resin Silicon Rubber Outdoor Voltage Transformer
JDZW-10RG
Beijing GFUVE Electronics Co.,Ltd.
Outdoor voltage transformer of the type JDZW-10 is single phase and epoxy resin silicon rubber insulated product, it's used for metering electric energy, voltage control and relay protection in 50/60HZ rated voltage less than 12kV electric system. It can be used for medial voltage AIS, or can be used for medial voltage switchgears. They can operate in all kinds of environments (such as wide range temperature (-50~70℃), high altitude, high humidity, high pollution or salt). This model JDZW-10 outdoor voltage transformer is also as voltage source to supply 220V voltage.
-
product
Relay Test Set
Cambridge Instruments & Engineering Co.
“CIE” Relay Test Set is ideal for Testing Protective relay, over current relay, earth fault relay by secondary injection method with help of digital timer.
-
product
Intelligent MCC Controller
MM2
The Motor Manager II (MM2) combines control functions and comprehensive motor protection in one package. This compactdevice provides sophisticated control and protective relaying at significant cost savings over the discrete devices normallyfound in a low voltage motor control center (MCC).
-
product
Primary Current Injection
PCI-600
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
product
Protection Relay Testing
Haomai Electric Power Automation Co.,Ltd.
1)Embedded industrial PC with 9.7" TFT LCD screen 2)Both online and offline test available 3)Can test both universal and IEC 61850 protection relay 4)6-phase current + 6-phase voltage output 5)Provide various type of messages which conforms to IEC 61850-9-1/9-2,GOOSE, IEC 60044-7/8 FT3 6)Able to test MU and optical digital signal 7)Built-in GPS module
-
product
Stator Ground Protection Relay
SEL-2664S
Schweitzer Engineering Laboratories, Inc.
Protect high-impedance grounded generators from ground faults at standstill, during startup, and while running with the multisine frequency injection and neutral overvoltage-based protection in the SEL-2664S.
-
product
Power Calibrator And Protection Relay Test Set
CP11B
Calmet Smart Calibration Devices
Single phase, class 0.02 and 0.05 power quality calibrator up to 120A and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
product
Three-Phase Transformer Demagnetizer
DEM60C
After a DC current test, such as winding resistance measurement, the magnetic core of a power or instrument transformer may be magnetized (remnant magnetism). It can cause various problems such as wrong diagnostics, inaccurate measurements on a transformer, inrush current at the start-up of a power transformer, or incorrect operation of protective relays due to magnetized CT cores. The best way to eliminate this source of potential problems is to use demagnetizer on the power or instrument transformer.The DEM60C is a fully automatic test instrument which performs three-phase transformer demagnetization. Transformer magnetic core demagnetization requires the application of AC current with magnitude decreasing to zero. DEM60C provides this AC current by internally changing the polarity of a controlled DC current. During the demagnetization process, the instrument supplies the current at decreasing magnitude for each step, following a proprietary algorithm. It can demagnetize single-phase and three-phase power transformers.The instrument can be connected to all three phases of a power transformer to be demagnetized, on either the primary or the secondary side. If a user selects specific vector diagrams for different types of transformers, DEM60C will run a specific demagnetization procedure for each transformer type (i.e., single phase, delta, wye/star, zig-zag.) without switching the test leads.DEM60C enables safe and efficient power transformer demagnetization. The instrument automatically regulates the injection of current and discharging energy from the inductance. During and after the operation, an intrinsically safe discharge circuit with an indicator rapidly dissipates the stored magnetic energy. The discharging circuit is independent of the power supply, which improves its reliability in case of loss of power.Test currents of up to 60 A DC enable efficient demagnetization of even the largest power transformers. Using a DV Win software, it is possible to control DEM60C externally.
-
product
Protection Relay Tester
PW866i
PW866i (6×32A, 4×300V) Protection Relay Tester could be used for testing all kinds of relays, also supports testing IEC 61850 combined relays. Its local control system is with 10.4inch LCD screen based on Windows system.
-
product
Universal relay test set and commissioning tool
CMC 356
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
product
Protective Relay Test Kit
PW460
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
product
Relay Protection Test System
RELAYSTAR 1600
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
product
Protection Relay Test Set
HT-1200 / 305
Wuhan Huatian Electric Power Automation Co., Ltd.
It can be used to test all kinds of traditional relays and protection devices as well as modern microcomputer protection.
-
product
Travelling Wave Fault Location Test Kit
PH Series
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
product
Automatic Relay Tester
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
product
Advanced Line Protection System
ALPS
ALPS is a multi-function digital protective relay system intended toprovide distance protection for HV or EHV transmission lines. It maybe applied on or adjacent to series compensated lines. It is availablefor single or three phase tripping applications. Typical operatingtimes are to 1 cycle.
