Filter Results By:
Products
Applications
Manufacturers
-
product
Emissions Reference Source
ERS
The ERS is a comb generator that radiates RF continuously every 2MHz over the range 30MHz - 1000MHz. Each 2MHz peak is precisely measured during the calibration process with the ERS orientated both vertically and horizontally. These measurements are correlated against a 3m OATS such that any fully implemented CISPR16 site, measuring at 3m and using height scanning, will read the same.
-
product
Area Scan Camera
Genie Nano-CXP
Introducing Genie Nano-CXP, a camera designed for full-throttle performance. Genie Nano-CXP builds on Nano's proven, industry leading reputation and leverages a CoaXPress 6Gbps interface to deliver the maximum throughput from leading edge high resolution CMOS image sensors.
-
product
acA4096-11gc, Color GigE Vision, 9 MP, 11 FPS Area Scan Camera
787061-01
The acA4096-11gc is a Color Basler Ace GigE Vision Camera with a 9 MP resolution and a maximum image acquisition speed of 11 frames per second. The acA4096-11gc uses a IMX267 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
product
HydroRANGER Series
The HydroRANGER is an evolution of mapping technology. This Airborne Topo-Bathymetric (ATB) system provides dual purpose topographic and bathymetric measurements for full scene mapping of shoreline systems. Utilizing a visible green spectrum laser with an elliptical scan pattern and measurement rates up to 200 kHz, the HydroRANGER provides a combination of high spatial resolution and spatial accuracy.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Scanning Electron Microscopy (SEM Analysis)
Rocky Mountain Laboratories, Inc.
Scanning Electron Microscopy (SEM Analysis) can produce images of almost any sample at magnifications of 15-300,000X. The SEM has tremendous depth of field allowing for imaging that cannot be accomplished using optical microscopy. Conductive and nonconductive samples can be imaged. When operated in the backscatter (BSE) detection mode, differences in material composition can be observed. Elemental analysis can be performed on any feature observed with an integrated Energy Dispersive Spectroscopy (EDS) detector.
-
product
LC/MS/MS Rapid Toxicology Screening System
Ver.3
This system improves the efficiency of simultaneous LC/MS/MS analysis methods by allowing the user to start analysis without time-consuming steps such as consideration of separation conditions and MS parameter optimization. Rapid simultaneous analysis methods with analysis times under 15 mins are included for 235 compounds including drugs of abuse, psychoneurotic drugs and sedatives. The system also provides optimised conditions for synchronised survey scans used in screening measurements (conditions adopted for the product ion spectrum as a threshold value for the intensity in MRM).
-
product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
product
Complete IP Module
Scan Ring Linker SRL
The Scan Ring Linker SRLTM - is a complete IP module that can be easily embedded into a CPLD, FPGA or ASIC on a PCB to reduce the complexities and costs of designing 1149.1 (JTAG) test infrastructure for designs that use multiple scan rings. The SRL IP module links any number of scan rings (secondary scan paths) into a single high-speed test bus, which permits devices on secondary scan chains to be independently tested and configured through a single 1149.1 external interface.
-
product
Fix, Speed Up and Maintain Your PC
Fix-It Utilities 15 Professional
System DashboardGet an instant overview of important system information, disk and memory space, battery life and processes running on your PC in one easy place.Look at system information on: operating system, default web browser, IP address, power settings and battery life.Know how much disk and memory space you are using, how much is free and your disk fragmentation level.See what processes and programs are running at startup and during active use.Data RecoveryEasily recover deleted files and data from your hard drives, USB drives, flash drives and memory cards.Disk Space SaverRan out of space on your drive? Are your files scattered everywhere? No Problem! Disk Space Saver scans and identifies where your large, duplicate, junk and Internet files are located.Get a visual display of your disk space usage that lists your biggest and duplicate files.Clear browser and download history, surfing activity cache and Internet cookies.Identify and remove unnecessary system clutter and junk files.Windows 8 CompatibilitySystem Suite is now fully compatibility with Microsoft Windows 8. Run System Suite with the peace of mind that you are fully protected and optimized.
-
product
AFM-Raman for Physical and Chemical Imaging
LabRAM Nano
Fully integrated system based on SmartSPM state of the art scanning probe microscope and LabRAM HR Evolution fully automated Raman micro-spectrometer. LabRAM HR Nano offers full automation and versatile compatibility with outstanding performance.
-
product
Direct conversion from cycle driven simulation data
Test program generator
Direct conversion from cycle driven simulation data (ATPG scan patterns) (WGL/TDL/STIL) to tester. TDL/WGL/STIL to tester conversion Supports STIL ext 0,1,2 constructs Easy to use and cost effective conversion solution Optimize tester resources usage Supports advanced tester features (Such as Xmode, Multi-port etc’) Compress and minimize vectors count Allow direct tester binary patterns creation
-
-
product
2D Automated Optical Inspection Systems (2D-AOI)
BF1 Series
Saki’s unique line scanning technology and coaxial overhead lighting enables high-speed accurate inspection.
-
product
Auto Wire Integrated Tester Series
LX-1024A+
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,．·Up to 1500Vdc/1000Vac Test Voltage ,．·1024 Max. Test Points ,(Max of all series)．·500 Max Files Memory,support USB or PC unlimited expansion,．·Using Embedded Linux operating system，．·Adopted high resolution colour 640*480 TFT LCD ,．·Large 320×240 LCD display ,．·Instant test time :0-60s , optional adjustment.．·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire.．·Auto Scan and Auto Pin Search ,．·The system provides advanced instant open-circuit, short-circuit, continuity test,．·Intermittent Conductance Test,．·Intermittent Open/Short Test ,
-
product
6U, CompactPCI/PXI module
CP213
The CP213 is a single-width, 6U, CompactPCI/PXI module with either 32 or 64 differential analog input channels that can alternately be configured under software control as 64 or 128 single-ended analog input channels. A 16-bit ADC scans each channel at a scan rate chosen by the user. The number of channels scanned and scan rate are software selectable. Scans may be triggered from either the internal clock, one of eight PXI backplane triggers, the PXI star trigger bus or an external SMB connector on the module front panel. Single and continuous scan operations are supported. If single scan operation is chosen, an interrupt may be generated at the end of the scan.
-
product
Tunable, Pulsed IR SW & LW OPO IR Source
Firefly-IR
Firefly IR is available in short-wave and long-wave models, providing broad wavelength coverage from 1.4-8.5 µm. The compact and sealed design requires no manual alignment, and can be used in a variety of applications in the lab and in the field. Wavelength selection and scanning is automated and performed via web browser or using a TCP/IP command set. Pulsed operation and high repetition rate provide high peak power and rapid data acquisition.
-
product
acA3088-57uc, Color USB3 Vision, 6 MP, 57 FPS Area Scan Camera
787070-01
The acA3088-57uc is a Color Basler Ace USB3 Vision Camera with a 6 MP resolution and a maximum image acquisition speed of 57 frames per second. The acA3088-57uc uses a IMX178 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
product
Leaf Area Meter
AM350
Compact and portable leaf area meter suitable for the accurate, non-destructive measurement of leaf area and associated parameters. It allows the scanned image to be saved in memory for future review of data & measuring technique
-
product
XJLink2-3030
The XJLink2-3030 provides convenient, integrated access to XJTAG’s powerful boundary scan test and programming tools from SPEA 3030 ICT machines.
-
product
Variable-Frequency Scanning Matrix
AllWin Instrument Science and Technology Co., Ltd.
1. Continuous Variable-frequency2. 4 way scanning matrix3. Constant pressure output
-
product
4-Sensor R-G-B (Prism) Color Line Scan Cameras
In addition to 3-sensor prism line scan cameras, JAI's Sweep+ Series includes a set of 4-sensor multispectral line scan cameras designed to simultaneously capture R-G-B image data in the visible light spectrum and image data in the near infrared (NIR) light spectrum.
-
product
Line Scan Camera
Linea Lite
Linea Lite makes line scan more accessible than ever. Designed with performance in mind, this camera offers superior color fidelity with 2k to 4k resolution and line rates from 12.5 to 50 kHz, with a GigE Vision® interface.
-
product
Medical System
Sentinel II
Chroma Systems Solutions, Inc.
The Sentinel II system provides fully automatic Electrical safety testing to IEC/EN/UL/CSA 60601-1. Sentinel II saves time by scanning patient connections for leakage current without powering down the medical device.
-
product
ROBOT-MOUNTED OPTICAL CMM 3D SCANNERS
METRASCAN-R
Part of the MetraSCAN 3D line-up, the robot-mounted MetraSCAN-R optical CMM 3D scanning systems are fast and accurate scanning solutions designed for 3D automated inspection of parts on the production line and on the shop floor. In combination with industrial robots, the MetraSCAN-R series increases the reliability, speed and versatility of on-line inspection and quality control (QC) process.
-
product
Digital Magnetic Compass
Prime
Prime is a full-featured 6-axis digital compass designed for flexibility and adaptability — the perfect fit for sonobuoys, ADCPs, side scan sonar, low-cost robotics, and other cost- sensitive applications.
-
product
Focus Control And Stabilization
Applied Scientific Instrumentation
The CRISP system is designed to maintain focus over time i.e. compensate for thermal & other factors that may cause the sample to drift out of focus over time. It also can be used to maintain a given focal point while scanning the sample in XY. If you are looking to find the optimal focal point while scanning through the sample in Z phase.
-
product
TRIOS AutoPilot
TA Instruments invites you to experience a new paradigm in software functionality. Unleash the full potential of your Discovery Hybrid Rheometer, Differential Scanning Calorimeter, and Thermogravimetric Analyzer with AutoPilot, a premium feature that enables process driven automation of TRIOS software. AutoPilot allows users to quickly and easily create automated routines: from test methods to data analysis and report generation. These routines empower laboratories to streamline and standardize operations and decision-making across local or global laboratory enterprises. From quality control to research and development, laboratory environments of all types will benefit from increased productivity, improved data precision, and reduced training time.
-
product
Easy3DMatch
Align a scanned 3D object with another scan or with a reference meshCompute the local distances between 3D scans and a golden sample or reference meshDetect anomalies such as misplaced features, geometric distortions, gaps, bumps,...Compatible with all 3D sensors that produce point clouds, depth maps or height maps
-
product
OBDLink SX Scan Tool
425801
OBDLink SX is the perfect entry level scan tool designed for the do-it-yourself mechanic. Despite its modest price tag, it is packed with advanced features normally found in more expensive scan tools. Includes the latest OBDWiz diagnostic software. USB interface.
