PCB Piezotronics, Inc.

Product

Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.

Product

Building Acoustics

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Measurements to evaluate and improve Building Acoustics are typically made to analyze and design noise control from room to room, or from outside to inside.   Noise sources such as music systems, televisions, appliances, traffic, aircraft, and manufacturing are all around us.  The field of Building Acoustics evaluates and designs the materials and methods to insulate and isolate us all from these sound sources when we are at work, rest, or enjoying leisure time.  The resulting data is useful for evaluating compliance with building codes and for proposing countermeasures for areas of concern.  These measurements often involve creating and measuring an artificial sound source, and then measuring the resulting noise in receiver locations.

Product

ICP Electret Surface Microphone

130B40

-

PCB Piezotronics, Inc.

130B40 - PCB Piezotronics, Inc.

Low-profile surface pressure microphone and preamp, prepolarized

Product

Multi-Conductor Cables

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

16 Channel, multi-conductor cables are shielded and wired for PCB® equipment specifically. Shielding minimizes noise when located near other power or signal cables. Custom versions are also available on request. Instrumentation-grade BNC / DB-50 connectors are provided to interface with Patch Panels and Signal Conditioners.

Product

Cryogenic Pressure Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Extreme Environment Dynamic Pressure Sensors.

Product

Force Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mount­ing holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.

Product

Pressure Sensors For Blast Testing

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.

Product

Precision Condenser Microphone

377B02

-

PCB Piezotronics, Inc.

377B02 - PCB Piezotronics, Inc.

1/2" free-field, prepolarized condenser microphone, typical sensitivity= 50 mV/Pa (+/-1.5 dB), 3.15 Hz to 20 kHz (+/-2 dB).

Product

Conformal Ballistic Pressure Sensor

Model: 117B31

-

PCB Piezotronics, Inc.

Model: 117B31 - PCB Piezotronics, Inc.

Conformal ballistics pressure sensor, 25-06 Rem, 270 Win, 280 Rem (7 mm Rem Exp), 30-06, 30-06 Springfield, 338-06 A-square, 35 Whelen, and 405 Win caliber cartridgesConformal ballistics pressure sensor for 25-06 Remington, 270 Winchester, 280 Remington (7 mm Remington Exp), 30-06, 30-06 Springfield, 338-06 A-square, 35 Whelen, and 405 Winchester caliber cartridges.

Product

ICP® Shock Accelerometers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.

Product

Miniature Quartz Force Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.

Product

Noise Monitoring Systems

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

It delivers 24/7 connectivity, continuous power capabilities, and a rugged design to simplify your long-term testing.

Product

General Purpose Quartz Force Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mount­ing holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.

Product

Torque Transducers

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.

Product

Cable Test Box

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.