HITEC Sensor Solutions Inc.
HITEC Sensor Developments designs and manufacturers load cells, strain gaged based force and torque sensors, instruments and complete test systems, and is an innovator of custom sensor solutions specific to a customer’s application.
- 978-742-9032
- 978-742-9033
- 10 Elizabeth Drive
Chelmsford, MA 01824
United States of America
-
Product
Weld Force Gauges
-
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders.
-
Product
Test & Measurement Sensors
-
These application-specific sensors are used in design validation, manufacturing and quality control to ensure passenger safety and improve vehicle performance. Each one is designed to solve a problem or address a technical requirement. Providing custom solutions for customer applications is what HITEC does best.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Torque Sensors
-
A device for measuring and recording the torque on a rotating system, such as an engine, crankshaft, gearbox, transmission, rotor, a bicycle crank or cap torque tester. Static torque is relatively easy to measure.
-
Product
PMAC 3000 Process Monitor and Control instrument
90424
-
The PMAC 3000 is a multi-functional Process Monitor and Control instrument, designed to operate with Sensor Developments Inc. Auto-ID sensors. Model 90424 has been enhanced to support quadrature encoders. This functionality is supported via Auto-ID and third party sensor programming. For easy verification, the encoder version will show the extension “E” when the software version number is displayed at power up.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Peak Track Instrument
90323
-
The model 90323 Peak Track Instrument is a general-purpose sensor readout device designed to complement our AutoID line of load cells and torque sensors. AutoID is a term that indicates that the calibration information for a sensor is stored on a chip inside the sensor’s connector. AutoID allows true “plug and play” operation without manual calibration procedures of any kind. The unit is also equipped with a 2-line alpha-numeric display and single button operation for simplicity.
-
Product
Mark I Single Setpoint Monitor
-
The Mark I is a self-contained unit featuring a single set point control. A simple two-step adjustment permits detection of an overspeed and/or underspeed condition at either 10% or 25% of operating RPM.
-
Product
Vehicle Test Sensors
-
Today's engines contain sensors to tell the vehicle's computer what's going on. Car sensors check for fuel-air mixture, incoming air temperature, wheel speed, and manifold pressure. They then tell your vehicle's computer what to do, based on that information.
-
Product
Mark II Dual Setpoint Monitor
95006
-
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
Product
Sensor Products: Weld Force Probe Auditing System
90061-XH Series
-
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders. The system consists of a handheld sensor and portable readout/ data logger (PMAC 2000).
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Threaded Load Button
2000 Series
-
This model is a threaded load button for tension and compression load measurements up to 5000kg/ 10000lb. Fully welded cover (for SS load buttons), amplified and digitised versions are available on request. We can also customise this sensor for other thread sizes and cable sizes
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
