Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
Product
Navigation Aid Panel Tester
MS 1114
-
The TE-247 is 19” rack mountable test equipment used for the functional acceptance of NAP-82 and CIP-82 of Jaguar aircraft LRU’s. Microprocessor Based design and MIL1553B Bus, RS232 interface used for testing LRU’s
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
Encoder And Decoder Unit
MS 2003
-
Encoder Decoder Unit is used to interact with ground station through PCM interface. Receives and transmits command/status information on Lakshya aircraft. Also provides real time clock synchronization, latitude/longitude information and IRIG-B Time. System is a digital, high speed FPGA controlled, intelligent unit to interact with various sub systems.
-
Product
Intel 80486 DX4
MS 1502
-
- ATE- Data Acquisition System- Process Control Industry- Industrial Automation
-
Product
Communication and Differential IO Board
MS 1707
-
- Four RS232 PORTS with full handshake- 16 Differential Input Channels- 16 Differential Output Channels- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
-
Product
CPCI Advanced Compute And IO Board
-
Advanced Compute & IO Board is high end Microprocessor based Mixed Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have digital I/O signals, analog I/O signals, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic (Programmable) data acquisition and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
Distance Measuring Equipment (DME)
MS 2002
-
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
PMC ARINC 717 Board
MS 1721
-
Bus Interface:- 32 Bit PCI Bus with PMC Interface. Speed of operation up to 66MHz. Spartan-3AN FPGA with ARINC 717 IP Core. One Channel ARINC 717 Transmitter and Receiver. Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals. Used to test all types of PCM based telemetry equipments. Configurable output signals format (parity, word length, Minor, Major frame, Bit position). User can configure the words and word positions in the frame. Driver interface for Windows2000/XP/VISTA and LINUX OS. Self Test future.
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
Mission Computer Software Integration Rig
MS 1124
-
The HSIR is the ground test facility and it simulates various LRUs/sensors interfaced with the HAWK Mission Computer. RIG consists of Industrial computers with Simulation modules, Acquisition modules, Video generator module and video display monitors. RIG provides the simulated inputs to both the MCs from each simulated sensor/ LRU through hardwired signals, through the MIL-1553B, Arinc 429, RS-422, RS232 and Ethernet etc. The rig is capable of testing two MCs together either of which can be used as the Bus Controller (BC) or the Remote Terminal (RT). The rig provides the facility to monitor and acquire the MIL-1553B, Arinc 429, RS-422, and RS232 Ethernet bus, Analog IOs, Synchro IOs, Discrete IOs and transactions that takes place between the MCs and various sensors/units. The RIG has the capability to test individual MCs also.
