Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
Product
Weapon Control System Test Set
MS 1102
-
- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design
-
Product
CAN Controller
MS 1529
-
- The "CAN" Bus Interface for Hall Controllers and Car controller- On-board EEPROM and KEY inputs for user settings parameters- LCD Module Interface- Eight 110 VDC Opto input interface- Six inputs interface (TINS, TUIB, TDIB, FIRE, FP, PRO-SW)- RS485 Interface and RS232 Interface (Optional)- Real time clock for Time Information
-
Product
CW Repeater Tester
MS 1108
-
The CW Repeater Tester is a computer-controlled system used to test CW Unit Electronics and its modules.
-
Product
Centralized Warning Panel
MS 1116
-
The Centralized Warning Panel Test Rig is used for conducting Pre Installation Test of Airborne Centralized Warning display unit of Advanced Light Helicopter.
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
ESI(Electronics Systems Integration Unit)
MS 2004
-
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
-
Product
3U CPCI ARINC 429 Board
MS 1725
-
- Bus Interface:- 32 Bit PCI Bus with 3 U Form factor- PCI to PCI Bridge Interface- Speed of operation up to 66MHz- 8 ARINC 429 TX and 16 ARINC 429 RX channels- 4 RS422 Channels- 16 TTL I/O Channels- Message Storage Buffer- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
Industrial Grade PCI DIO 96 Board
MS 1817
-
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
-
Product
Data Retrival and Analyzer Unit
MS 1200
-
*Retrieves the Data from Magnetic / Solid State Recorders (Supports JAGUAR, AN32, IJT, ALH Platforms)*RS232/RS422/Bi-Phase/USB interface with PC AT*Presents Error Messages and Test Reports*Replay, Analysis and printout of selected parameters*Calibration facility for ADR and DAU*Portable System for Snag Analysis of Aircraft*Reports in Tabular/Graphical formats*Used to check serviceability of ADR, DAU without removing from aircraft
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
-
Product
ESI Test Jig
MS 1543
-
This Test System designed to test the analog, discrete, Ethernet, RS232, RS422, Synchro /Resolver and SPI Signals. It is standalone test equipment and has GUI ATP Software interface with laptop/PC through RS232/Ethernet Interface.
