Physitemp Instruments
Physitemp Instruments Inc is an electrical/electronic manufacturing company.
- 800.452.8510
973.779.5577 - (973) 779-5954
- 189 Sargeant Avenue
Clifton, NJ 07013
United States of America
-
Product
Air And Gas Probe
GT-1
-
GT-1 Air and Gas Probe - 24'' #304 stainless steel shaft. Wooden Handle. For instant readings of temperature gradients in environmental chambers, freezer boxes, etc. Diameter is .3/16'' diameter. Immersible. Maximum temperature 200°C, Time constant Seconds. 5 foot lead. Not isolated.
-
Product
Thermal Microscope Stage For Petri Dish
TS-4SMP
-
With our TS-4SMP Thermal Stage for Petri Dish, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C. The collar on the stage is designed to accommodate a 35mm 'Nunc' petri dish. The collar may also be removed for use with slides.
-
Product
Gauge Type T Thermocouple Wire
W-TW-20
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Foot Rest
VFR-1
-
The optional footrest is designed to be used with the Vibratron-II. The foot rest is 12'' long x 8'' wide x 4.25'' high with adjustable non-slip leveling feet ( feet are adjustable to add up to 1/2'' of additional height if needed). Surface of the footrest is a white hygienic non-skid vinyl covering and can be easily cleaned between uses. The unit is large enough to accommodate both feet and may also be used as an armrest when testing upper extremities. The weight of the unit is approximately 4.5 pounds. The footrest can also be purchased as an option to the NTE-2A .
-
Product
Needle Microprobe
MT-29/2HT
-
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Flexible Implantable Microprobe
IT-21
-
IT-121 Flexible Implantable Microprobe - Implantable in semi-solids and tissue with 21 gauge needle (supplied). Ideal for subcutaneous and cranial temperatures in small animals. Also for immersion in various solutions. Totally sheathed in chemical resistant Teflon™. Maximum Temperature 150°C . Isolated. Probe diameter .016" (21 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.08 seconds.
-
Product
Gauge Type T Thermocouple Wire
W-TW-26
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Thermal Sensitivity Tester
NTE-2A
-
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
Product
General Purpose Probe
HT-2
-
HT-2 ''Workhorse'' General Purpose Probe - designed for temperature measurement of liquids, gases and semi-solids. Plastic handle with straight 9'' stainless shaft. Not good for surface temperatures. Maximum temperature 400°C, Time constant 0.5 Seconds. 5 foot lead. Not isolated.
-
Product
Animal Temperature Controller- Dual Feature
TCAT-2DF
-
This is a combination version which includes both and AC outlet for controlling primarily resistance loads such as heat lamps, AC powered warming blankets and a low-voltage, low noise DC output for heating pads. This version allows you to controls a variety of different loads.
-
Product
Gauge Type T Thermocouple Wire
W-TW-30
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Needle Microprobe
MT-29/1HT
-
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
General Purpose Probe
BT-1
-
BT-1 General Purpose Probe - Probably our best general purpose probe designed for temperature measurement of solids, liquids, gases and semi-solids. Welded stainless-stell shaft, plastic handle. Tip is .028'' diameter bent at right angle to probe to facilitate accurate surface measurements. Immersible. Maximum temperature 240°C, Time constant 0.15 Seconds. 5 foot lead. Not isolated.
