-
Product
24 V DC Power Supplies
-
*Space-saving design*High power reserves*Low heating of the control cabinet*Low inrush current*Safe switch-off by circuit breakers in case of short circuit
-
Product
DC to AC Power Inverter
TE-1201UB
-
Help to operate all kinds of devices need the AC power, such as electric lights, kitchen appliances, power tools, TVs, radios, computers and more. The extra USB can provide power for using/charging mobile phones and digital devices conveniently.
-
Product
Static Elimination
-
Fraser Anti-Static Techniques Ltd
Cost-effective passive, AC or 24 V DC technology solutions for static neutralisation, dust removal and cleaning.
-
Product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
-
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Modular DC Electronic Load
N3300A Series
-
The new N3300A Series of dc electronic loads is fast, accurate, and ideal for increasing production throughput in high volume dc power supply manufacturing. This series consists of a full rack width (1800 watts max) mainframe and a half rack width (600 watts max) mainframe, and 7 interchangeable electronic load modules. The modules provide a variety of voltage, current and power ratings. New dc connectors for test system configurations are now available on all modules.
-
Product
Adapter/Stainless Steel
WADP-NFSM-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
3.5" Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, VGA/LVDS, Dual LANs And Audio
CAPA318
-
The CAPA318 features the Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake) with low power consumption. The integrated 3.5-inch embedded board is highly expandable and customizable. It comes with RS-232 ports, USB 3.0 ports, USB 2.0 ports, IN/OUT digital I/O ports, VGA port, LVDS port, and Gigabit Ethernet ports with Intel® i211AT Ethernet controller. For storage needs, the CAPA318 provides one SATA-600 socket and one mSATA interface. Additionally, Its compact and fanless design makes it perfect for use in space constricting environments. Additionally, the 3.5” single board computer can handle a wide operating temperature range from -20°C to +70°C (-4°F to +158°F) and requires +12V DC power input to ensure operational stability in a variety of harsh environments. This cost-effective 3.5” embedded motherboard is suitable for IoT/M2M related applications, industrial control, self-service terminals, digital signage, POS/kiosk displays, just name a few.
-
Product
A-A-S General Purpose Probes
General Purpose Probe
Current Rating (Amps): 2Average DC Resistance lower than (mOhm): 30Test Center (mil): 39Test Center (mm): 1.00Full Travel (mil): 30Full Travel (mm): 0.76Recommended Travel (mil): 20Recommended Travel (mm): 0.51Overall Length (mil): 310Overall Length (mm): 7.87Rec. Mounting Hole Size (mil): 31.5Rec. Mounting Hole Size (mm): 0.80Recommended Drill Size: #68 or 0.79 mm
-
Product
CPRI Interface Panel Kits for Connectivity Testing
-
RFS’ CPRI Interface Panels are used to test fiber connectivity between Optical Base Band Units (BBU) and Remote Radio Heads (RRH), allowing cell operations and system performance engineers to ensure the best performance without having to disconnect the fiber optical system or disrupt service. In addition, the CPRI panel enables easy RF over CPRI testing at the bottom of the tower, reducing the need for unnecessary tower climbs, thus minimizing maintenance cost and overall OPEX for customers. The RFS CPRI panel is bundled with RFS’ high-quality fiber optic jumpers, providing an end-to-end solution that includes HYBRIFLEX® fiber-to-the-antenna DC and F/O solutions.
-
Product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
DC Blocking L-Band Splitter Combiner
PD5980
-
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
Product
Standard 3.00 (85.00) - 6.00 (170.00) Non Replaceable General Purpose Probe
G-S-R
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 780Overall Length (mm): 19.81Rec. Mounting Hole Size (mil): 86Rec. Mounting Hole Size (mm): 2.18Recommended Drill Size: #44
-
Product
High Voltage Probe
HVP-40DM
-
*DC 40KV CAT II Pollution 2.*2000MΩ Impedance.*3999 LCD display.*Accuracy 1.0% full range.*T.C. 100 ppm/oC*400V/4KV/40KV, 3 range.*Resolution 0.1V/1V/10V.*PEAK HOLD, Auto power off.*CE, TUV GS, UL, CUL, IEC1010
-
Product
Slip Ring Test System
-
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
Product
IP67 DC Blocking Splitter Combiner
PD5123
-
INSTOCK Wireless Components, Inc
PD5123 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5123 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45SH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
Product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
Product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX02
Frequency Extender
The N5295AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
Product
Powered VME64x Crates
6U VME64x 395-x Mini
-
The VME395-x mini crate series offers hot-swappable, redundant power supplies in a 9 slot, compact but modular designed VME64x chassis. A front-side-plug high performance DC fan is used for cooling with front to rear air flow.
-
Product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL09
-
INSTOCK Wireless Components, Inc
GPSL09 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while blocking the DC current path. Max voltage rating at the DC blocked ports is 10 VDC; maximum current rating is 50 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL09 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Isolated Relay I/O Board
104-IIRO-16
-
The 104-IIRO-16 is a low-cost board that provides isolated input and output for PC/104 Bus computer applications. The board has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen electro-mechanical relay outputs. The Change of State Detection capability of ACCES’ Model 104-IIRO-16 sets this board apart from the competition. An Economy version can be ordered as Model 104-IIRO-16E which has no Change of State Detection or IRQs. Also available is Model 104-RO-16 which has 16 relay outputs only.
-
Product
Alternate 0.50 (14.00) - 2.50 (71.00) General Purpose Probe
P2662BG-1C2S
General Purpose Probe
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 68Full Travel (mm): 1.73Recommended Travel (mil): 50Recommended Travel (mm): 1.27Overall Length (mil): 575Overall Length (mm): 14.60
-
Product
DC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
DC load banks for all voltage levels and power test applications, available in a variety of models including portable and fixed models.
