PD
voltage discharge within an insulator causing dielectric breakdown.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD Test, Partial Discharge Test
-
Product
PD Coupler
-
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
Product
Portable PD Monitoring
ASM-P
-
The ASM-P can be configured with up to 32 PD sensor channels. If excessive discharge is detected, the ASM-P raises an alarm that can be configured either locally or by email/SMS. This enables the long-term assessment of plant conditions to be carried out quickly and easily, from any remote computer.
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
-
Integrated PoE LLDP and Load Emulation in a Single Instrument. IEEE 802.3at and 802.3bt LLDP Compliance Analysis. Independent, Per-Port 802.3at and 802.3bt LLDP Emulations. Flexible Single and Dual Signature PD LLDP Emulations. One-Click LLDP Protocol Capture and Analysis. Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing. Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's. Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's. Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's. Available for PSA-3000 and PSL-3000 Platforms.
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
-
The optional LLDP Emulation feature allows a PSA-3000, PSL-3424L, or PSL-3000 test port to behave just like an 802.3at or 802.3bt PD that uses LLDP to convey its power demands. 802.3 PoE LLDP is a special variant of LLDP protocol that involves handshakes and protocol timing between a PSE and a PD.
-
-
Product
USB PD Power Supply/Module ATS
8000 Series
Power Supply
The USB 3.1 specifications has three major features which are 10Gbit/s transmission speed, USB PD (Power Delivery) with support for 100 watt charging power, and the standard Type-C connector/cable that can be inserted with either side. It is expected to meet all kinds of data / video transfer applications. The advent of USB PD may consolidate the specifications of various power converters and the laptop, monitor, printer or Hub that implements USB PD is no longer a simple power-consuming device but able to supply power to other devices. The USB PD DRP (Dual role port) function allows the built-in USB PD module to deliver a maximum of 100 watts of power through the Type-C interface. To make sure the USB PD Type-C output power does not supply invalid voltage or poor power output characteristics with excessive noise that can damage the power consuming device and cause unsuccessful startup, each USB PD power supply or module has to be fully tested during production to ensure the product features meet the design specifications. This ensures high-quality products are provided to the market to gain acceptance.
-
Product
PD Calibrator
-
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
Product
Portable PD Acquisition Unit
AQUILA
-
Techimp AQUILA has been expressly designed to respond to all these needs being a robust and compact portable all-in-one PD detection station providing a full range of options ideal for on field applications. It can cope with the toughest outdoor conditions while taking measurements on any electrical asset. 15 years of service experience has been condensed in this unit integrating TECHIMP innovative PD detection technology with multiple connectivity (Wi-Fi, Fiber Optics, USB, Bluetooth) and power supply.
-
Product
Positive Displacement (PD) Meters
-
Positive Displacement (PD) flow meters are volumetric flow measurement instruments ideal for low flow rates, highly viscous fluids, and measurement of flows involving starts and stops or pulsing. Positive displacement flow meters are similar in design to the gear pump. The principle of operation is reversed however; instead of the gears driving the fluid, the fluid drives the gears. A non-intrusive hall-effect sensor detects the movement of the gear and as each gear tooth passes the sensor, a square wave pulse is produced and a discrete volume of liquid is measured. The resulting pulse train is proportional to the actual flow rate and provides a highly accurate representation of the fluid flow.
-
Product
PD Pipe & Cable Locator
PD / PD-H
-
Audio frequency 750cpsMaximum 100v outputFine Tune knob and LED's to easily match maximum impedanceInterrupter feature on oscillatorLCD meter on receiverReceiver loud speaker or headset useHoliday detection on buried pipe (PD/H)
-
Product
Cable Diagnostics Systems - VLF/TD/PD
-
The Tan Delta (TD) series of diagnostic test instruments was developed to help cable engineers evaluate the condition of their MV and HV cables.
-
Product
Fibre Linked EHV And Distributed Assets PD Monitoring System
EHV-PDM
-
The EHV-PDM is a PD monitoring system designed for application on critical EHV and distributed assets, where the monitoring point could be many hundreds of metres or tens of kilometres apart. Fibre linked monitoring points transmit PD data over long distances to the main monitoring unit, which then processes the data and displays the results on a secure customer web front end.
-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
PoE LLDP Emulation (PSE) & Analysis for 802.3at & 802.3bt
-
The IEEE 802.3 specifications require that Type 2, Type 3, and Type 4 PDs implement PoE LLDP and use the Power via MDI TLV for power negotiation. This requirement therefore applies to any PD that draws more than 13 watts. The PDA-600 family includes an option to flexibly emulate any PSE while capturing and analyzing the LLDP power negotiation protocol from a PD.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
Product
Field Testing Services
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT offers three levels of testing services both domestically in the US and globally. With the best quality products, complete PD solutions, rich on-site testing experience, experienced partial discharge experts and field engineers, PMDT also provides PDExpert Services -- professional on-site partial discharge detection and location services to help the customers find the potential risks, evaluate the operating status of the electrical assets, and deliver complete and final problem solutions.
-
Product
VLF Testing and Diagnostics System
PHG 80 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 80 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltage* Compact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
-
Intuitive graphical user interface. Configures up to 24 2-Pair or 4-Pair ports for "snaked data path" testing. Verifies all PSE connections in the defined data path. Sequences user-defined PD emulations and PSE powering.Verifies powering to user-defined loading on all selected ports. Configures looped data paths across the selected ports. Support of 802.3at / 802.3bt LLDP power negotiations (PSL-3424L).
-
Product
PD Free Test Transformer
-
Wuhan Fanke Transformer Manufacture Co., LTD
PD Free Test Transformer
-
Product
Valves Testing Equipment
-
A PD or PHD Pinhole Detector is ideal as it has an audible alarm which sounds when a fault is found. Additionally, the test voltage can be set accurately, which is particularly important when testing thin linings. A DCCT mains-powered porosity tester can be used if the process needs to be incorporated into a production line
-
Product
Shielded Rooms
-
HIGHVOLT Prüftechnik Dresden GmbH
Electromagetic field and line-conducted interference needs to be eliminated in order to measure low-intensity partial discharges with a PD background noise level (≤ 1 pC) in accordance with IEC 60270.
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
Product
Cable Diagnostic Tools
-
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
Substation Series Testers
GTPD-92
-
Partial discharge（PD） is a pulsed discharge that produces a series of physical phenomena and chemical changes such as light, sound, electrical and mechanical vibrations in and around electrical equipment.
-
Product
LAN Router
BB-SR30009110-SWH
Router
SmartFlex, Global, 5x Ethernet, PoE PD, Plastic, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
Multi-Channel PD System Locator
PDiagnostic Series
-
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnostic is a portable system that utilizes Ultra-High Frequency (UHF), Acoustic Emissions (AE), High-Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV) sensors to detect, analyze, and locate the PD signals in real time for a multitude of medium and high voltage electric power equipment.The multi-channel PDiagnostic system locates PD on power equipment down to a meter by utilizing Acoustic-Electromagnetic Combination Location Technique, Time Difference of Signals’ Arrival (TDOA), Partial Discharge Signals Separation (PDSS), and 3D Positioning Technology with PC software included.The system features advanced PD diagnostic capabilities, automatic PD type pattern recognition, and accurate PD location capabilities. The PDiagnostic is an ideal trouble-shooting tool for your PD programs. Severity is determined and maintenance suggestions are provided accordingly.
-
Product
I2C/SPI Exerciser and Protocol Analyzer
PGY-I2C/SPI-EX-PD
-
Prodigy Technovations Pvt. Ltd.
I2C Protocol Analyzer and SPI Protocol Analyzer (PGY-I2C/SPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-I2C/SPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective I2C or SPI designs for its specifications by configuring the PGY-I2C/SPI-EX-PD as Master/Slave, generating I2C/SPI traffic and decoding the I2C/SPI protocol decode packets
