LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Digital Tachometer
TM-3100 series
-
TM-3100 series is a new model of digital tachometer which responds to changes in diverse measurement objects by adding function in order to match your application.The each model of TM-3100 series has the most fundamental function in rotational measurement (display of rotation speed, BCD output, analog output or comparator output) and can be customized by adding optional cards.The fluorescent display tube of TM-3100 series greatly improves stability and readability instead of using LED as old models.
-
Product
Quantum Sensors
-
Apogee offers two types of quantum sensors. The Full-spectrum Quantum Sensors feature an improved detector that provides accurate measurements under all light sources, including LEDs, right out of the box. The Original Quantum Sensor is less expensive and great for measuring all light sources except certain LED colors, where post-measurement correction factors need to be applied to achieve accurate readings.
-
Product
Drop Weight Tear Tester
DWTT
-
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
Product
SparkFun 16 Output I/O Expander Breakout
SX1509
-
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
Product
Handheld Water Quality Meters
LAQUA PD220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- Dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation- 0.01 mg/L or 0.1% DO resolution- Compensates salinity, temperature, and atmospheric pressure - Up to 2 DO calibration points - With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting the meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Multi-Battery Tester
MBT-1
-
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Product
Chassis - up to Four 8x1 or 4x2 Modules, or up to Four 8k Modules in a 4 RU Chassis
HXV/32-MF
-
These Chassis controls up to 4 8x1 modules, 4 4x2 modules, or up to 2 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
Video Signal Generator
MSPG-7800S
-
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneousl and sufficiently examining a large-sized display device.
-
Product
Transmissive Optical Encoder Module
EM1
-
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
Product
Optical Chopper
-
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combination. Chopping frequency is set by adjusting a ten-turn dial or by applying an external DC voltage to the BNC input. Reference output is a TTL pulse and is in-phase with chopping action. The 5 digit led display gives a direct read-out of the chopping frequency. Power: 90-130V or 180-260V; 50/60Hz; 12VA max. Power supply included. Choppers are often used together with lock-in amplifiers.
-
Product
International Wireless 6V/12V Battery and 12V/24V System Tester
SBT1
-
Schumacher Electric Corporation
PERFORM BATTERY AND SYSTEM TESTS WIRELESSLY FROM YOUR SMARTPHONE OR TABLET.For 6V and 12V automotive batteries (SS EFB and AGM included) and 12V/24V charging/starting systemsEasy and fast Bluetooth® pairing Works with SBT1 SchulinkTM app, which includes eight language settings.Performs Battery Test, System Test, Start-Stop Test and EV Battery Test Email or text test results – stores 2,000 test records Test batteries with as little as 1.5V3 LED indicators (Blue: Connected, Green: Power, Red: Trouble)On/Off button20-inch cable with durable clamps3.7V rechargeable internal lithium ion batteryContents: (1) SBT1 tester (1) Manual
-
Product
Mini Bug Detector II
P7050
-
Peace of mind is now within your reach. The Mini Bug Detector™ offers state of the art protection against wireless microphones and transmitters. Perfect for securing homes, offices and hotel rooms, the unit not only detects such devices, its LED display and audio tone actually pinpoint the precise location of bugs. The audio alarm can be turned off for discreet sweeps, while the unit’s sensitivity adjustment minimizes false alarms. The Mini Bug Detector™ features wide range circuitry that enables it to detect concealed transmitters operating on frequencies from 50 MHz to 3 GHz, exposing most high frequency transmitters as well as more common VHF and UHF bugs. You didn’t know they were listening…until now.
-
Product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
-
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
Product
Bidirectional Weight Indicator
480
-
Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity
-
Product
Terminal Test Kit (19 PCS)
3605
-
Peaceful Thriving Enterprise Co Ltd
1. Check high and low voltages (power and ground) on 6, 12 and 24V system.2. 4mm connection for banana plugs.3. LED indicates red for power (high) and green for ground (low).4. High impedance protects sensitive electronic ignition components.5. Connects red lead to power source and black lead to ground source.6. 1.8m long heavy-duty dual leads with battery clips and spring strain relief.7. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
Product
Industrial All-In-One Touch Panel PC Based On Intel Atom® X6000E Series Processors
STC2-EHL Series
-
- Intel Atom® x6000E series processors (Elkhart Lake)- 15.6” 16:9 LCD panel with LED backlight with 50,000 service life- With up to 1920 x 1080 resolution- 10-point PCAP touchscreen- Anti-fingerprint surface treatment for ease of cleaning and enhanced readability- IP 65 rating for water and dust protection- Robustness with wide 9-36V DC input- Ease of installation with optional VESA mount•
-
Product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
-
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
4 & 5 Pin Trailer Circuit Tester
PT7866
-
Traces each lighting function to the terminal in question. Plugs into the trailer plug. Each LED light corresponds to the circuit being energized. Provides an easy to connect ground terminal for trailer lighting set-up.
-
Product
ColorPAL Color Sensor
28380
-
The ColorPAL is a miniature color and light sensor which, through its RGB LED, doubles as a color generator. For sensing color, the ColorPAL uses its LED to illuminate a sample, one color component at a time, along with a broad-spectrum light-to-voltage converter to measure the light reflected back. The amount of light reflected from the sample under illumination from each red, green, and blue LED can be used to determine the sample’s color. The ColorPAL works with non-fluorescent reflective surfaces, preferably those in contact with its light shroud.
-
Product
15" Fanless Panel PC With Intel® Celeron Quad Core J1900 Processor
PPC-3150-RJ9
-
15" TFT XGA LED Panel with resistive touchscreenEmbedded Intel Celeron processor, quad core J1900 2.0GHz onboardSystem memory up to 8GB DDR3L 1333 SDRAMSupports one internal SATA 2.5" HDDSupports one Mini PCIe socket, two Gigabit EthernetFanless and compact size with low power consumputionSupports five RS-232 and one RS-232/422/485, besides six RS-232 and two RS-422/485 are optional by requestSupports one mSATA socket
-
Product
Network Analyzer, Lan Tester, LED
72-6706
-
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
Product
Power Supply QP305E 2x30V/5A
-
*On / Off switch output section*4 independent regulated DC output*Independent serial and parallel output*Constant voltage and current*Low ripple and noise*Four digit LED displays three*16 hours at full loadd
-
Product
LED Test
-
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
Product
Handheld Water Quality Meters
LAQUA PC210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Refrigerant Leak Detector w/ Gooseneck
RLD10
-
UEi Test & Measurement Instruments
The RLD10 makes pinpointing leaks as easy as one two! Detect leaking refrigerant using the high sensitivity mode then switch to the low sensitivity mode to pinpoint its source. If background noise makes the audible tic hard to hear, you can count on the color scaled LED indicators. With the RLD10 you'll get the latest in refrigerant detection at a great price.
-
Product
LED Light Bar Module For USC-360 Series
USC-P03-B302
-
Interface: USB, OS support: Windows 10 and Android, Operating temperature: 0 ~ 40 °C.
-
Product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H110, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS960-511-PoE
-
Featuring a multi-core CPU, IP40-rated rugged design, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control, the IPS960-511-PoE provides an all-in-one solution that addresses the needs across various machine vision platforms and automatic inspection cases. The IPS960-511-PoE is powered by the LGA1151 socket the 7th & 6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® H110 chipset. The intelligent vision system comes with dual DDR4-2133/2400 un-buffered SO-DIMM sockets for up to 32GB of system memory as well as supports rich camera interfaces for connecting industrial cameras, including four IEEE802.3at PoE LAN ports and four USB 3.0 ports. Its vision I/O integrates a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The IPS960-511-PoE also supports lighting dimming control to identify object characteristics for different inspection. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
Product
Programmable Setpoint RelayProtection Relay, Trip Relay
CRD-005 and CRD-020
-
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbulletCRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbulletCRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbulletCRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbulletLid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bulletRed LED lamp lights to indicate when the threshold level has been tripped
-
Product
Hand Held Loss Test Set with Return Loss Option
LTSH1315
-
The KD Optics LTSH1315 is a combined laser or LED source and power meter designed to make attenuation testing in the field easy, reliable and consistent. A return loss option is available for 850nm multimode, 1310nm and 1550nm singlemode.
-
Product
Vol-Con® Solenoid Voltage Tester
61-076
-
*Extremely rugged and reliable*Vibrates when AC voltage is present*Indicates AC/DC voltage level*Replaceable leads with shielded probe tips (IEC61010-031 compliant)*Bright, long-life LED™s and neon indicator lamp*Dual voltage indication for backup safety*2-year warranty
