Near Field Communications
a set of protocols enabling <10 cm contactless communicaiton. Also known as: NFC
See Also: Communication Protocol, Modbus, Data Communications, NFC
-
Product
Mini Burst Field Generators
-
Mini burst field generators are small and handy burst generators used to detect weak spots in the device under test.
-
Product
Field Strength Analyzer
SRM-3006
-
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
Product
RTM Communication Board
MS 3636I
-
CPCI Rear IO Communication Board is a signal conditioning and interface board for CPCI Integrated Communication Card (MS3635i). This board has required signal conditioning and interface circuits for RS422. Two 96 Pin Euro Connectors are used to interface all IO’s.
-
Product
3-axis Magnetic field Sensor
FLC3-70
-
Compact, low-power, 3-axis fluxgate magnetometer for the measurement of weak magnetic field down to nanoteslas. Due to its rugged design and extended operating temperature range suited for automotive and aerospace applications and for deep drilling tools.
-
Product
Magnetic Field Generator
PFM61000-8A
-
PFM61000-8A Magnetic Field Generator is high reliability test equipment with stable performance, specially designed for electrical and electronic products for measuring immunity characteristics and requirements of normal frequency magnetic fields. It provides an accurate basis for the tested equipment in the immunity test of normal frequency magnetic field. The generator can imitate the magnetic field environments such as residential, commercial, industrial and mining enterprises, power plants, as well as middle and high substation. It fully meets IEC61000-4-8 and GB / T17626.8 standards.
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
Communication Test Software for MODBUS RTU
ComTest Pro
-
ComTest Pro Communication Test Software for MODBUS RTU Devices via Serial and Ethernet. This complementary program allows users to test and troubleshoot MODBUS RTU communication by sending single or multiple read or write commands to the device. The software offers comprehensive data-logging, data-formatting and error checking features.
-
Product
MXI-Express Cable with Communication Levels up to Gen 3 x8
781042-100
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Communication Protocol Test Harness
-
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
Product
Electromagnetic Field Tester
-
The EMF tester is designed to provide user a quick, reliable and easy way tomeasure electromagnetic field radiation levels around power lines, home appliancesand industrial devices.
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
Serial Communications
-
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.
-
Product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
-
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
Product
Industrial Communication
-
Reliable data flow and transparent communication across all production processes have become indispensable in automation. The main goal of industrial communication is to integrate all plant areas from the control to the field level in a networked system. Because consistent and powerful data networks increase the availability and efficiency of machines and systems.
-
-
Product
Measuring Solar Fields
ISET Sensor
-
The solar radiation sensor is characterized by a simple and compact but precise structure. Use in balancing monitoring systems for simple, fast and reliable information about the functioning and solar "energy yield" of a PV plant. For site surveys, monitoring and other fields of survey technology.
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
-
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
Product
PCI Express Communication Card
ECU-P1524LSE
-
A specialized network interface device designed to provide zero-packet-loss, zero-recovery-time redundancy (IEC 62439-3) for critical infrastructure. It typically features 2-3 SFP ports for HSR/PRP, connects to a host system via PCI Express, and supports SR-IOV to enable multiple virtual machines (VMs) to share the card's resources for high-availability communication, often used in substation automation or industrial IoT.
-
Product
Magnetic Field Camera: mapping for MRI applications
MFC2046
-
MRI and NMR spectroscopy applications require a highly uniform magnetic field, within at most a few ppm. NMR is the only magnetic measurement technique capable of providing a field map with that degree of precision. Introduced 25 years ago, Metrolab’s NMR Magnetic Field Cameras have revolutionized field mapping for MRI magnets. They reduced acquisition times from hours to minutes, positioning errors to fractions of a millimeter, and they rendered human and drift errors negligible. Now, meet the latest generation NMR Magnetic Field Camera, the MFC2046! Map any magnet with the New generation of MFC probe arrays. Magnetometer Teslameter Gaussmeter
-
Product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
Product
Field Probe Positioner
-
The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.
-
Product
RS-422/485 Serial Communication Card
LPCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
CPCI Or PXI Communication Interface Board
MS 1706
-
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Hand-hold Field Intensity Meter
LM870-H
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Character LCD displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
Product
Serial Communications Card
104-ICOM-2S
-
The Model 104-ICOM-2S Serial Communications Card can be installed in a PC/104 stack and provide effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
TestTools for Lab & Field
-
Analyzer designed to be used on the field to generate maps including measurements of the field quality of service, enabling identification of reception issues and efficient troubleshooting.
-
Product
Field Strength Meters
-
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
Product
Laser- Field of View Measuing System
SIMES
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*For checking vehicles in order to meet standards concerning field of view*Developed in cooperation withTÜV Rheinland
