Safety Test
Check to determine whether a device is free from hazards.
-
product
Safety Test Panel for Water Cooler
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
product
Electrical Safety Test Solutions
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
product
Safety Test Panel for Luminaire Fixture
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
product
Pulsed Withstand Voltage Safety Test
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
product
Heavy Impact Tester, Battery Safety Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
product
Safety Test Panel for Geyser
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
product
Optical Radiation Safety Test
EN62471-C
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
product
Safety Test Panel for Mixer
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
product
EST-200 Emission Safety Test System For Toys
Hangzhou Everfine Photo-E-Info Co., LTD
The system can test the radiation intensity, irradiance, light color expansion angle, peak wavelength, dominant wavelength, bandwidth, etc. of various toy light emitting devices. The measurement conditions meet the CIE127 standard, and the test report meets the ENIEC62115:2020 standa
-
product
Safety
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
product
Testing Services
DTB is the largest independent testing laboratory in the United States with a full spectrum of testing services all under one roof. We provide a wide range of environmental, dynamics and vibration, EMI/EMC, ballistics, optical, ordnance release, and safety and survival testing.
-
product
Pulsed Withstand Voltage Safety Test
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
product
Electrical Safety Tester
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
product
Electrical Product Safety Testing
We specialize in pre-certification evaluation, CE marking self-declaration testing, UL / CSA / TUV certification/verification testing. Other agency witness testing may be arranged upon request. CKC’s, and our partners, are equipped to test to a wide array of products including information technology, audio/video, test and measurement, medical and industrial.
-
product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety. -
product
Multifunctional testers
MI 3125 BT EurotestCOMBO
The MI 3125BT EurotestCOMBO performs all the necessary tests for installation safety testing on TT and TN systems. The large graphic display with backlight offers easy reading of results, indications, measurement parameters and messages. Two LED Pass/Fail indicators are placed on both sides of the LCD. MI 3125BT EurotestCOMBO contains integrated characteristics of fuses and RCDs (including B type) for the evaluation of test results.
-
product
Pump, Hydrostatic Test, 15,000 psi
9901-150L
Hydrostatic test pump may be utilized as a standalone unit or combined with any of our reservoirs, safety test chambers, test fittings or other optional equipment to achieve a complete hydrostatic test system. with integral safety test chamber.
-
product
Testing & Measurements
Kiwa Dare performs measurements and tests in the area of CE marking, Automotive and FCC. The laboratory is specialized in EMC, RED and Product Safety tests for household, industrial, automotive, medical, telecom, maritime, railway, aerospace and military equipment.
-
product
Photovoltaic and Electrical Installation Testers
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
product
OST-500 Optical Radiation Test System
Hangzhou Everfine Photo-E-Info Co., LTD
OST-500 is an optical radiation safety test system with 200-3000 nm wavelength range, refer to IEC/EN 62471/CIE S009, IEC/TR 62778, GB7000.1-2015, GB/T 20145, IEC/EN 60598 Annex P., IEC/EN 60598 Annex P. IEC/EN 60432, IEC/EN 60335, GB/T34075-2017, GB/ T34034-2017 2009/125/EC and other relevant standards. The system is equipped with a precision automatic dual-axis turntable, which can automatically find and obtain the maximum radiation position, and automatically measure the photobiohazard value of various lamps and lamp systems (LED products, ultraviolet lamps, lighting sources and lamps, etc.) at the maximum radiation position, and carry out safety classification.
-
product
Safety Testing
Whitelegg has over 80 years of experience in the design manufacture of market-leading electrical safety test equipment. Our unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications for use in a variety of industries including manufacturing, construction, education, utilities, aerospace, calibration and anywhere else where there is a requirement for electrical safety testing or precision resistance measurement.Test equipment is cost effective, helps you to minimise expense, improve efficiency and increase profit. Whether you need electrical test equipment, environmental test, power analysers or HV Test Equipment, we stock the products to meet your demands, all backed by our first-class technical support if you have any problems using the equipment.
-
product
Handheld Online PD Detector
PD-SGS
BAUR Prüf- und Messtechnik GmbH
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
product
Resistive Current Tester
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
product
Display and Analysis Software
IADS
Curtiss-Wright Defense Solutions
IADS telemetry client software is the integrated display and analysis portion of the IADS data display, processing, delivery and archive software suite. IADS client facilitates real-time mission analysis and raises situational awareness, safety monitoring, and test point clearance capabilities to a new level.
-
product
Wound Component EST Scanner
19035
The quality verification tests for wound components consist mainly of AC/DC Hipot tests and insulation resistance (IR) tests. The Chroma 19035 wound component EST scanner series perform safety tests for motor, transformer, and heater related wound products.
-
product
Battery Testing Chambers
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
product
Multi-Channel Hipot Tester
19020
The hipot test is one of the major test items in electrical safety testing. All electrical components and products including transformers, capacitors, power supplies, chargers and home appliances require hipot testing.
-
product
Food & Beverage Testing Products
If you are in the food and beverage industry and are vigilant about the safety of the items you manufacture, or if you are a contract testing service lab looking for complete food safety testing products, Bio-Rad offers food safety testing products designed for small, medium and large volume laboratories.
-
product
Battery Testing Chambers
ET-SERIES
These Chambers are designed and manufactured to meet various types of battery testing requirements of its customers by keeping all safety options in mind against any harmful explosions or ignitions and user safety while testing these batteries for environmental stress conditions
-
product
Battery Test Equipment
Shenzhen Bonad Instrument Co., Ltd.
The tests that can be performed by lithium-ion battery safety testing equipment include temperature cycling test, thermal abuse test, high altitude low-pressure simulation test, vibration test, shock test, external short-circuit test, forced internal short-circuit test, drop test, crush test, impact test, nail penetration test, burning test, etc. These test items mainly apply to various lithium-ion cells such as 18650 cells and prismatic cells, lithium-ion batteries, lithium-ion battery modules, lithium-ion battery packs, and so on.BONAD battery safety testing equipment complies with various standards such as IEC 62133, IEC 62133, UL 2580, UN 38.3, UL 1642, etc. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
