Product

Shield Level / Pathloss Equipment

SG1000B/PR1000A

-

Praxsym

SG1000B/PR1000A - Praxsym

The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.​To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.

Product

42-Pin Male Nano-Pitch To 42-Pin Male Nano-Pitch, Shielded OCuLink Cable

785486-01

-

NI

785486-01 - NI

Nano-Pitch Male to Nano-Pitch Male OCuLink x4 Cable, 1 m

Product

RF Shielded Test Enclosure, I/O Intensive Device Tests

JRE 1720

-

JRE Test, LLC

JRE 1720 - JRE Test, LLC

Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. A JRE exclusive, our triple door locking mechanism allows easy single handle door operation. Ventilation is standard with our JRE exclusive honeycomb style vents in enclosure rear and door.

Product

MAX31856 Thermocouple Sensor Arduino Shield

SEN-30007-T

-

Playing With Fusion Inc

SEN-30007-T - Playing With Fusion Inc

Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.

Product

BCX Basic Cyclic Corrosion Cabinet

-

Atlas Material Testing Solutions

Atlas Material Testing Solutions

Basic cyclic tests are used to qualify a coating or material for a specific end use on a pass-fail basis, or determine the probability of corrosion of a specific material.

Product

Shield Level / Pathloss Equipment

PAMS & PAMS-C

-

Praxsym

PAMS & PAMS-C - Praxsym

PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures.   Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks.  Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure.  Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.

Product

Fixed Writing Surface for Double-Bay 24" RA & RC Cabinets

WS2-124

-

ELMA Electronic, Inc.

WS2-124 - ELMA Electronic, Inc.

This fixed shelf / writing surface for a double-bay RA & RC cabinets spans the full width of the cabinet and extends 18” in front.

Product

MAX31855 T-Type Thermocouple Arduino Shield

SEN-30004-T47

-

Playing With Fusion Inc

SEN-30004-T47 - Playing With Fusion Inc

Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.

Product

802.11a,b,g RF Shielded Test Enclosure

JRE 0709-A

-

JRE Test, LLC

JRE 0709-A - JRE Test, LLC

Containing all the capability of the larger JRE enclosures, the compact 0709-A is ideal for small wireless devices such as; 802.11a,b,g WLAN access points, VoIP devices and other small RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.

Product

802.11a,b,g RF Shielded Test Enclosure

JRE 0814-A

-

JRE Test, LLC

JRE 0814-A - JRE Test, LLC

Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.

Product

Shielding Cube

CMQ200

-

Rohde & Schwarz GmbH & Co. KG

CMQ200 - Rohde & Schwarz GmbH & Co. KG

The R&S®CMQ200 is a compact and fully integrated solution to cover most 5G devices in various applications. The drawer concept enables fully automated handling in manufacturing environments. The robust mechanical design ensures millions of test cycles for reliable mass production environments. The flexible cube design covers applications for smart devices, CPEs, RFIC and prototypes. R&S®CMQ200 is ready for 5G and other technologies in the frequency range from 20 GHz to 77 GHz.

Product

RF Shield Box

LTL R21001

-

Liveon Technolabs

LTL R21001 - Liveon Technolabs

Liveon Technolabs LTL R12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL R12001 RF shielded test enclosure can comfortably house the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.

Product

802.11a,b,g Dual RF Shielded Test Enclosure

JRE 0814-2R-A

-

JRE Test, LLC

JRE 0814-2R-A - JRE Test, LLC

Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.

Product

RF Shielded Test Enclosure, Slim rack mountable

JRE 1724A

-

JRE Test, LLC

JRE 1724A - JRE Test, LLC

Designed for testing devices with a flat form factor that need plenty of I/O, the rack-mountable JRE1724A is ideal. Similar to our JRE1724, but not as high, you can place multiple devices within its large footprint. Dual I/O panels allow for a multitude of connectors and interfaces. The JRE1724A comes standard with dual honeycomb style vents - pictured is the enclosure with optional cooling fan and USB2.0 interface.