SPI
assures volume and area of paste application.
-
Product
Bi-Directional Level Translator
IFB-10001
-
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
Product
ARM 9 System on Module
MS 1515
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
72 channel FPGA Logic Module
XLM72
-
XLM72 is a FPGA based logic module with 72 I/O ports. Featuring two 64 Mbit SPI (Serial Peripheral Interface) memories, from one of which its FPGA boots upon power-up, complex logic operations can be programmed and saved on-board.
-
Product
Unipolar D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply d/a converters in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+® products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
Product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
-
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
Product
Voltage Output D/A Converters
-
Analog Devices offers a large family of resistor string and R-2R voltage output (VOUT) D/A converters (DACs). From 8 bits up to 20 bits of resolution, single to 40 channels, integrated or external reference, parallel, LVDS, serial SPI or I2C interface, with high temperature operation, we have a D/A converter to suit your application. We provide precision, buffered, and unbuffered rail-to-rail VOUT D/A converters with up to ±1 LSB INL and DNL specifications and excellent offset and gain error. Our D/A converters work well in a wide variety of open-loop or closed-loop systems—adjusting gain, offset, and many other signals.
-
Product
SOM Module
TEO820-ZU2CG
-
Sundance Multiprocessor Technology Ltd.
Xilinx Zynq UltraScale+ XCZU2CG-1SFVC784EZU2, 784 Pin Packages4 x 5 cm form factorRugged for shock and high vibration2 x 512 MByte 32-Bit width DDR4 SDRAM2 x 32 MByte (2 x 256 MBit) SPI Boot Flash dual parallel4 GByte eMMC Memory (up to 64 GByte)B2B Connectors: 2 x 100 Pin and 1 x 60 Pin
-
Product
Temperature, Humidity, Pressure and Gas Sensor
BME680
-
The BME680 is a digital 4-in-1 sensor with gas, humidity, pressure and temperature measurement based on proven sensing principles. . This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price!
-
Product
16-Bit, 12 GSPS, RF DAC and Direct Digital Synthesizer
AD9164
-
The AD9164 is a high performance, 16-bit digital-to-analog converter (DAC) and direct digital synthesizer (DDS) that supports update rates to 6 GSPS. The DAC core is based on a quad-switch architecture coupled with a 2× interpolator filter that enables an effective DAC update rate of up to 12 GSPS in some modes. The high dynamic range and bandwidth makes these DACs ideally suited for the most demanding high speed radio frequency (RF) DAC applications. The DDS consists of a bank of 32, 32-bit numerically controlled oscillators (NCOs), each with its own phase accumulator. When combined with a 100 MHz serial peripheral interface (SPI) and fast hop modes, phase coherent fast frequency hopping (FFH) is enabled, with several modes to support multiple applications.
-
Product
3D Solder Paste Inspection (SPI)
TR7007 SII
-
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
Product
SparkFun Pulsed Radar Breakout
A111
-
Does your project require high-precision, cutting-edge distance measurement? Or maybe speed, motion, or gesture-sensing? We're not talking about simple ultrasonic or even infrared here, but 60GHz radar! Well say hello to the SparkFun A111 Pulsed Radar Breakout! The A111 is a single-chip solution for pulsed coherent radar (PCR) and comes complete with an integrated antenna and an SPI interface capable of clock speeds of up to 50MHz. Though the A111's primary use case is distance-sensing, it also supports applications in gesture, motion, material, and speed-detection at distances of up to two meters.
-
Product
CyberOptics SE Series
SE Series
-
The CyberOptics SE Series offers the most accurate and repeatable, high speed 3D solder paste inspection in the market today. Utilizing the most advanced sensing technology, CyberOptics SPI products will provide manufacturers the reliability needed to compliment your overall screen print process improvement strategy.
-
Product
Function Generators
-
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad
-
Product
VVDI Programmer
-
MC9S08 series secured and unsecured , MC68 HC series (9) 12 secured and unsecured, MC9S12 series secured and unsecuredV850 series, H8X series, R8C series, R5F series, PCF79XX, EEPROM SPI, I2C, & mu WIRE, PIC 12F, 16F, 18F, Infineon TRICORE, Infineon XC2xxxx, Infineon XC164CS, ST10F series, ST7 series, STM8 series, ATMEL- Atmega 8, 48, 16, 32, 64, 128, 256, MPC560 series, SPC560 series, Fujitsu MB91F
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
5D SPI
-
On Mek Solder Paset Inspection systems, items which are better inspected in 2D, such as area offset and bridging, are viewed in full colour. Using colour inspection the ISO-Spector S2 SPI can tell the difference between paste, solder mask, silk screen and other PCB features and the SPI system can intelligently give you accurate results. Volume and height measurement in 3D are combined with the 2D inspection in Real-time, to give a True colour 3D image. Other 3D SPI systems only inspect in the 3rd dimension, (Z axis) and make extrapolated assumptions about the 2D image.
-
Product
Trusted Platform Module Compliant With TCG 1.2 / 2.0 Specification And TCG Software Stack 1.2 / 2.0 Via SPI Connector On CPU Card.
PCA-TPMSPI
-
Trusted platform module compliant with TCG 2.0 specification and TCG software stack 2.0 via SPI connector on CPU cardHardware based data protection solution for storage device encryption and decryptionDimensions (L x H) : 20 x 22 mm (0.79" x 0.87")Support Model: PCE-5033/5133
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.
-
Product
ContactLAB Spy
-
Laboratory class spy and protocol analyzer for easy, non-intrusive capture and analysis of communication between contact cards and readers using SWP, ISO 7816, SPI and I2C protocols.
-
Product
Channelized Up-Converter
UPCV Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Wide Choice of Frequency Ranges *IF to Ka-Band Solutions Available *Integrated Filters *Gain Control *USA, RS232 or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
Multibus Ethernet Card
MS 1750
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
SparkFun Qwiic Micro:bit Breakout (with Headers)
-
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
Product
Silicon Oscillators
-
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
Multiplying Current Output D/A Converters
-
Analog Devices offers a wide range of high precision, multiplying current output (IOUT) D/A converters (DACs) that feature ±1 LSB INL and DNL specifications, from 12-bit up to an industry-leading 18-bit resolution. Our portfolio includes single and multiple D/A converters in small packages with parallel or serial SPI interfaces. Multiplying current output R-2R D/A converters allow for an external amplifier that’s optimized for specific applications and that does not require reference buffering, which enables high linearity. The SoftSpan™ feature allows software selectable output spans, therefore eliminating the need to add precision gain stages and the associated external jumpers, precision resistors, and amplifier circuitry. Integrated precision resistors allow for reference inversion, bipolar offset, and offset and gain adjustment.
-
Product
Low Phase Noise Frequency Synthesizer
-
Corech’s low phase noise frequency synthesizer series generates precise and stable frequency signals across a wide frequency range, available in SPI serial interface. These cost competitive, rugged and compact module are the ideal choice for RF & Microwave systems such as communication systems, test and measurement equipment, radar systems etc.
-
Product
SparkFun SAMD21 Development Board
Qwiic Micro
-
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
Product
LoRa 1W Breakout
915M30S
-
Do you need power? This breakout for the 915M30S module from EBYTE is a 1W (30dBm) LoRa transceiver. LoRa is great for long range (miles), low power (in sleep), and low data rates (~500bps). This breakout board is designed to connect to any platform that has SPI and 6 available GPIO. We include a robust edge mount RP-SMA connector to connect large LoRa (915MHz) antennas. In addition, the on-board U.FL connector can be used if you need to get outside a metal enclosure.
