Extender Boards
move out from slot circuit card giving access thereof.
See Also: Extenders, Extender Cards, Test Boards, Bus
-
Product
Extended L-Band
-
Quintech Electronics and Communications Inc.
A piece of equipment that routes a large number of RF (radio frequency) signals, typically satellite signals, to any combination of outputs.
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
Digital I/O Board w/CoS IRQ
104-DIO-48S
-
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
Product
I/O Board With Two COM, Four USB 3.0, One Gigabit LAN, And HDMI For PICO880, PICO500, PICO300
AX93276
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x HDMI, 1 x Gigabit LAN, 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
Product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
-
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
I/O Board With Two COM, Four USB 3.0 And Audio For PICO880, PICO500, PICO300
AX93299
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 1 x Audio (Mic-in/Line-in/Line-out), 4 x USB 3.0*Dimension: 118 x 40 mm*Compliant Product: PICO880, PICO500, PICO300
-
Product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit, Custom Version
APCI-3501-8-2P
-
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
Product
High Speed Data Acquisition Board
MS 1800
-
*Bus Interface:- 64 Bit PCI Bus with PMC Interface*Virtex-4 FPGA based design*32 channel digital I/O signal*RS232 & RS485 Interface*32MB Flash*2MB Static RAM for data storage*Analog Inputs:- 2 Channel*Input Resolution:- 14 Bits*Sampling rate up to 80MSPS*Filter:- Low Pass Filter for all channels*Two Analog Outputs*14 bit Resolution*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
IC-INT-VPX6d, 6U VPX Dual Intel® Xeon® Single Board Computer
IC-INT-VPX6d
-
The IC-INT-VPX6d is a 6U OpenVPX digital signal processing (DSP) embedded computing board for defense applications. It is a key element in high -performance embedded computing (HPEC) designs.
-
Product
PCIe I/O & Comm Board
79C3
Multifunction I/O
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
I/O Board With Two COM, Four USB 3.0, VGA And Audio For PICO880, PICO500, PICO300
AX93275
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x VGA, 1 x Audio (MIC-in/Line-out), 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
Product
PCI Express A/D Board
AD8-3000 Series - Dual 8 bit, 3 GS/s
-
The AD8-3000 series has one or two 3000 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
Interface Module
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
Extend Your Shop's Diagnostic and Programming Capabilities
Mongoose®-Plus
-
Mongoose-Plus offers industry-leading J2534 pass-thru technology enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. This line of economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Mongoose-Plus is engineered to work with each OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
-
Product
Isolated Analog Expansion Board
MSXB 085
-
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Low Voltage Boards
-
- 6 or 8 independently controllable full floating channelsup to 64 V- Up to 60 W Max channel output power- High resolution on voltage set- Programmable TRIP parameter- Programmable ramp up / down- Current generator operation in overcurrent condition- Overcurrent programmable protections- Individual remote sense lines- Up to 0,2 mV voltage monitor resolution- Up to 1 mA current monitor resolution- Voltage ripple smaller than 3 mVpp
-
Product
Single-Function I/O Boards
-
NAI offers, and continues to support, primary or single-function I/O boards designed for a specific, single-purpose application. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements. They are specifically designed for rugged defense, industrial, and commercial applications.
-
Product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit
APCI-3501-8
-
*8 analog output channels*Optical isolation 500 V*Settling time 30 µs typ.*14-bit resolution (13 bit for 0-10 V)*Output voltage: ±10 V, 0-10 V (switchable through software)*Output voltage after reset: 0 V*Each output channel has its own ground line (without optical isolation from the others)*Driver capacity: 5 mA/500 pF*Short-circuit protection, EMI filters*Noise neutralization of the PC supply*Creeping distance: 3.2 mm acc. to DIN VDE 0411-100*Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary*2 digital input channels, 24 V, isolated*2 digital output channels, 24 V, isolated
-
Product
COM Express Boards
-
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
-
Product
6U CPCI Processor Board
CP67001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP67001 is a CompactPCI® processor board based on China local-manufactured Phytium FT1500A/4 4 cores ARM processor, with more than 10-year lifecycle. Designed with ARM v8 Architecture, 28nm process technology and fine-grained power optimization technologies, its CPU integrates 4 ARM cores with CPU clock speed up to 2.0 GHz. Combined with the maximum power consumption of 15w, CP67001 is highly applicable for making low-power-consumption solutions.Equipped with Intel82580, CP67001 supports 4x Gigabit Ethernet; 4x SATA 2.0 and 8x USB 2.0; 1x16 PCI Express for XMC and PMC; SM750 graphic controller with resolution up to 1920x1080p. CP67001, as a single board computer has up to 64GB flash memory, provides outputs including HDMI, DP, DVI and VGA, and provides 2 serial ports with one port supports RS232/RS422/ RS485 configurable through software. In addition, CP67001 supports GPIO and can meet customized demands in different situations.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
Alchitry Cu FPGA Development Board (Lattice ICE40 HX)
-
If you are not needing a lot of power to start your FPGA adventure, or are looking for a more economical option, the Alchitry Cu FPGA Development Board might be the perfect option for you! The Alchitry Cu is a "lighter" FPGA version than the Alchitry Au but still offers something completely unique. FPGAs, or Field-Programmable Gate Arrays, are an advanced development board type for engineers and hobbyists alike to experience the next step in programming with electronics.
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
SBC347A 3U OpenVPX Intel Rugged Single Board Computer
SBC347A
-
The SBC347A Rugged SBC features the 5th Generation Core i7 processor from Intel, with integrated graphics and memory controller plus quad core processing up to 2.7 GHz.
-
Product
Meter Test Board
MTB-3200
-
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
