Firmware
-
product
PCI CONET Controller
A2818
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
product
Electronic Compass - 3-axis Solid-State Magnetometer, 2-axis Electrolitic Tilt Sensor
Revolution
The Revolution electronic compass combines a precision 3-axis solid-state magnetometer and a rugged 2-axis electrolytic tilt sensor to provide accurate heading and tilt measurements over a broad range of environmental conditions. The firmware and signal processing algorithms have been refined and improved over three prior generations of electronic compasses to deliver the ultimate in performance from the available sensor data.
-
product
GPIB Serial Interface Boards
ICS's GPIB to Serial Interface boards are designed for in-chassis applications. Select boards with transparent data transfer or boards with smart firmware that can add an IEEE-488.2 interface to any serial device
-
product
FPGA Fast Fourier Transformation (FFT)
eXpert / Fast Fourier Transformation
Fourier Transform Analysis is Advanced On-board FPGA Technology a powerful signal-processing technique used in a wide variety of applications. GaGe’s eXpert FFT firmware allows CompuScopehardware to perform Fourier Analysis within its on-board processing FPGA.
-
product
AT Command Slave/Peripheral
AT command module series
Raytac's AT command module series comes with AT command firmware pre-programmed which helps developers enjoy a Design Saving & Time-To-Market journey
-
product
Calibrators
Handheld calibrator is an exceptional instrument performing precision measurement of pressure, temperature, current or voltage. The base unit includes application-specific firmware for convenient instrument calibration and logging of associated data. In addition, the ATE-2 has the ability to interface the system with a computer, data acquisition system or dumb terminal via the standard USB interface.
-
product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
Broadband Test
458-3SLB
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
product
Fully Compliant ASi-5 Transceiver ASSP
ASI4U-V5
The ASI4U-V5 is the industry’s first silicon solution to fulfill the ASi-5 (Actuator-Sensor-Interface version 5) standard for industrial network equipment that enables comprehensive Industry 4.0 applications. The ASI4U-V5 ASSP comes with a completely verified and field-proven firmware that fully implements ASi-5. Hence, integration of ASi-5 into any application is very easy, as the complexity of the fieldbus is hidden by the chip and the firmware.
-
product
Dual Digital Multichannel Analyzer
780 MCA Family
The 780 MCA family integrates advanced firmware algorithms operating Digital Pulse Processing for Pulse Height Analysis (PHA). The processing algorithms can be easily adapted to different detectors and application ensuring effective data analysis even at high count rates. It provides advanced tools for configuring baseline restoration, pile-up rejection. Thanks to the two input simultaneous acquisition, the modules are able to manage coincidence and anti-coincidence logic between detectors, allowing the user, for example, to easily take advantage of background rejection or anti-Compton techniques. These MCAs may provide at the same time energy, time stamp and the digitized pulse in a configurable time window (e.g. including the rising edge region) in order to perform further online analysis. Acquisition settings and basic mathematical analysis are performed through the CoMPASS and MC2Analyzer software, providing energy spectra with up to 16k channels, which can be exported and imported in ASCII or N42.42 compliant files. CAEN further provides drivers for the supported communication interfaces; configuration software tools, C and LabVIEW libraries (CAENComm, CAENDigitzer, CAENDPP), demo applications and utilities.
-
product
Filter Design System - Mode Analyser
EA-300
The EA-300 is a stand alone unit with internal firmware and a large colour display. It connects to the outputs from a standard LISN and feeds the results to any standard EMC analyser or receiver. The EA-300 prompts the user through the steps necessary to fully characterise the emissions from the EUT, then will output via the screen the recommended filter component values that would reduce these emissions to acceptable levels.
-
product
AT Command Master+Slave / Central+Peripheral
AT command module serie
Raytac's AT command module series comes with AT command firmware pre-programmed which helps developers enjoy a Design Saving & Time-To-Market journey.
-
product
LCRZ Tester
DU-6218
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 55 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Firmware for High-speed HDLC Mode
OP-FW10
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
product
Rack Mount Stage Controller
RM-2000
Applied Scientific Instrumentation
*2U 19" Rack Mount Control Unit: 22.8D x 48.3W x 8.1H cm (9" x 19" x 3.2").*100 MHz Microcontroller for Faster Command Processing and Servo Control.*Closed-Loop DC Servo Control of up to Four Motorized Axes.*0-10 Vdc DAC Output for Additional Analog Control.*Firmware Upgradeable via Serial Connection.*Remembers Last Position on Power Up.*LCD Display Shows Axes Coordinates and Status.*USB or RS-232 Serial Control with Rates to 115200 Baud.*"Zero", "@", and "Home" Buttons on Joystick.*Left- or Right-Hand Joystick Unit.
-
product
Next Generation Subsea Inertial Navigation Systems
TOGSINS
The new TOGSINS builds on core TSS fibre optic gyro technology by incorporating inertial navigation (INS) capability. As with TOGS, it is available in three standard heading accuracy variants: 0.1° (TOGSINS1), 0.3° (TOGSINS3) and 0.5° (TOGSINS5), all rated for operational depths to 4,000m or 6,000m giving you a range for all your needs.Inertial position data is produced using an INS algorithm, within the firmware framework of TOGS, whilst attitude data is delivered via accurate roll/pitch measurement of 0.01° (TOGSINS1) and 0.05° (TOGSINS3 and TOGSINS5), and a heave performance of 5cm or 5%.
-
product
USB 32-Bit Whacker
PIC32MX795 Development Board
The new version of the UBW32 now uses the PIC32MX795 IC. Based on the work of Brian Schmalz, the UBW32 is a small development board for the new PIC32MX795 32-bit CPU from Microchip. The UBW32 is breadboard friendly and includes all of the external circuitry needed to get the PIC32 up and running. Power can be provided over USB or from an external source. It has three push buttons (Reset, and two user-defined buttons) and five LEDs (Power, USB, and three user defined LEDs). All of the 78(!) of the PIC32's I/O pins are broken out. The board comes pre-loaded with a USB bootloader and special UBW firmware that accepts simple serial commands to control the various I/O functions.
-
product
Toolbox.NET
Software for Data Exchange
The Toolbox .NET provides firmware upgrade capabilities and data transfer stored in internal instrument memory to a PC. The Toolbox .NET is based on Microsoft .NET Framework 3.5 and will operate with the following Raytech products:
-
product
ColorFlex EZ Coffee Spectrophotometer
Hunter Associates Laboratory, Inc.
The easy-to-use ColorFlex EZ Coffee is specifically built to meet and exceed your needs in measuring the color of roasted coffee grounds. It makes it easy to define the degree of roasting. Coffee color scales provided in firmware include: HunterLab Coffee Color Index (HCCI), SCAA Number & SCAA Roast Classification.
-
product
Distortion Detector PLUS
DD-1+
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
product
Quad 12.0 Gsps 16-bit DAC FMC+ Module
DAC-Q30
The DAC-Q30 FMC+ module from DEG is a high sample rate, 16 bit quad channel DAC module. The Analog Devices AD9174 DAC device operates at 3.0 Gsps natively and up to 12.0 Gsps in interpolation mode. A VITA 57.4-compliant FPGA Mezzanine Card (FMC+) interface, the DAC-Q30 offers industry wide platform compatibility with the PCIe/VME/VXS/VPX carrier board of your choice. The DAC-Q30 and associated HDL firmware are compatible with AMD FPGAs.
-
product
Capacitor Leakage Current Meter
DU2316/2317
Delta United Instrument Co., Ltd.
Leackage Current range display: 0.0001uA ~ 20.00mAAutomatic or Manual trigger with CHARGE/TEST/DISCHARGE100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceHi / Lo current limit setting & PASS/FAIL judgment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Wind Power Solution
ECO MITSUBISHI
The ECO MITSUBISHI is custom-made with firmware and fixtures designed specifically for Mitsubishi turbines: 1000, 1000A, MWT 2.4. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
SparkFun GPS Breakout
XA1110 (Qwiic)
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the XA1110 GPS module from GTOP, this board utilizes the MediaTek MT3333 chipset, loaded with specialized SparkFun firmware that enables both I2C and serial ports simultaneously. Using I2C means you won’t have to tie up your serial port with GPS, leaving it open to other possibilities.
-
product
Multi-Axis Stage Controller
MS-2000-WK
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
product
27” Open Frame Gaming Monitor With Touchscreen
GM-270
ADLINK’s GM-270 27” open frame gaming monitor is specially designed for casino gaming applications, suitable for embedding in video lottery terminals, slot machines, and self-service kiosks. The GM-270 gaming monitor features 10-point PCAP touch screen, optional cover glass, custom I/O modules, and tailored firmware.
-
product
VPX Power Supplies
Dawn is the leader in VITA 62 compliant power supplies for the mission critical market. Wide range of standard features, highly configurable through custom firmware.
-
product
Full System Simulator
Simics
Wind River Simics is a full system simulator used by software developers to simulate any target hardware from a single processor to large, complex, and connected electronic systems. This simulation enables the target software (board support package, firmware, real-time operating system, middleware, and application) to run on a virtual platform the same way it does on the physical hardware.
-
product
Handover Test Systems
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
