-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Design for Test Service
-
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
Product
PCB Test And Design-For-Test Services Group
-
ntellitech has a very experienced consulting and test development organization that is dedicated to provide our customers with high-quality design and test services. Choosing Intellitech Test Services can help you lower the risk of adopting a new Design-for-Test methodology or speed your product to market when you need to deploy a test solution quickly.
-
Product
Design-for-Test
-
As designs move to smaller and more complex process technologies, ensuring devices are thoroughly tested becomes a bigger challenge. Mentor Graphics provides whole-chip test solutions that can help improve test -- and, therefore, device -- quality as well as control, or even reduce, the cost of test.
-
Product
MIMIC® Redfish Simulator
-
The MIMIC Redfish Simulator, the industry's first integrated simulation tool supporting Redfish, allows developers to perform real world, integrated device simulations. MIMIC simulates thousands of Redfish-capable devices. MIMIC allows suppliers of Redfish devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will be able to handle the scales of messages and different types of requests to work properly when deployed across heterogeneous environments.
-
Product
Accessibility Test Probes
TF-24 Series
-
Accessibility Test Probes are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Power Quality Analyzer
-
Power quality analyzer is a product carefully developed by our company and specially designed for field test of three phases, multi-functional and intelligent, man-machine operation and concise and comprehensive test instrument. It is easy to use, large LCD screen display, high resolution, interface in both Chinese and English, shock-proof shell structure and so on. Can simultaneously measure the 4-channel current (ABC three phase and neutral wire current), 4-channel voltage (ABC three-phase voltage and neutral line voltage to ground), the peak value of current voltage, maximum/minimum value over a period, three-phase imbalance factor, short-time voltage flicker, transformer K factor, active power, reactive power, apparent power, power factor and displacement power factor, active power, reactive power, apparent power, total harmonic distortion and harmonic, etc; Display real-time waveform, harmonic ratio bar charts of current voltage; Dynamically capture instantaneous change of voltage current, monitoring starting current, monitoring the power parameters and generate the alarm list, generate the trend chart for a long time record test data.
-
Product
NIBP Simulator
vPad-BP
-
vPad-BP, part of the vPad-A1 family, is a NIBP (non invasive blood pressure) simulator designed to test the accuracy and repeatability of the NIBP function on Patient Monitors. User programmable settings allow for easy on site configuration to accommodate new models of NIBP devices.
-
Product
Ball Pressure Apparatus
BP-20
-
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat.
-
Product
DC Power Products
-
West Mountain Radio offers a variety of power management devices to protect both the radio equipment and the power systems they are connected to. These devices provide both battery charge management and load management features. They are for public safety, commercial, marine and amateur radio applications. All products designed and tested by Ham radio operators.
-
Product
Benchtop/Portable Cable/Harness Wiring Test System
CKT1175-10
-
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
Product
Vacuum Bottle Testers
-
Vanguard Instruments Company, Inc.
The VBT-75 S2 is Vanguard's second generation microprocessor-based, portable, 75kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuitbreaker vacuum bottles in the field and at the shop.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k with SPDT
40-293-123
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Commutator Testing Unit
-
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Bleeder, Pressure Indicator - Brake, F/A-18 Hornet
-
F-18 Brake Bleeder. This unit is designed to test, monitor and bleed the brake systems of F/A-18 Hornet fighter aircraft.
-
Product
2-Way Power Dividers
-
KRYTAR 2-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 2-way power dividers can also be manufactured to meet military specifications.
-
Product
RF/Microwave ATE Systems
-
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
SMI Protocol Exerciser and Analyzer
PGY-SMI-EX-PD
-
Prodigy Technovations Pvt. Ltd.
SMI Protocol Analyzer (PGY-SMI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-SMI-EX-PD is the leading instrument that enables the design and test engineers to test the respective SMI designs for its specifications by configuring the PGY-SMI-EX-PD as Master/Slave, generating SMI traffic and decoding the SMI protocol decode packets.
-
Product
Temperature Calibrators
-
Highly accurate dry well temperature standards designed for testing and calibrating a broad range of thermometers, temperature sensors, thermocouples, RTDs and temperature switches used in military and industrial applications.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 46 W, PXI Programmable Power Supply
779647-11
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
PXI 40Amp 14Volt 2xSPDT Automotive Relay
40-181-001
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Test Probes
E-Series
-
Your product descriA full portfolio designed for general purpose test on bare boards, surface mount assemblies and other forms of test specially to meet any needs.ption goes here.
-
Product
Walk-In Temperature & Humidity Test Chamber
-
Weiber walk in humidity test chambers are conceptualized and designed to create test chambers to study and contemplate the effects of different environmental parameters such as humidity, temperature applications tests involving micro-organisms, plants, tissues, electronic components etc. apart from various customized industrial and research applications. Our humidity test chambers have a variety of usage in R and D laboratories, research studies and product testing facilities across the globe. Apart from that, these chambers have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories. We specialize in both standard and customized humidity test cabinets, specifically designed to meet the challenging demands of various scientists for individual and specialized research applications.
-
Product
Tester & Programmer
TP-TACT
-
TP-TACT is designed to test the efficiency and program the operating range of electronic turbocharger controllers.
-
Product
Pressure/Vacuum Calibrators
-
Compact, completely self-contained unit designed for calibrating and testing pressure gauges, transducers, pressure switches, and other pressure-sensitive instruments up to 2,000 psi with an accuracy of ±0.25% of full scale.
