-
Product
Current Tester
MIG0624
-
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
Product
PXIe High-Speed Source/Measure Unit, 13 V, ± 1 A or 6 V, ± 3 A, 18 W
M9111A
Source Measure Unit
The M9111A is a 1-slot, 2-quadrant PXIe module that provides stable, glitch-free sourcing and sinking, and high accuracy measurements. It offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. With industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading, the M9111A SMU speeds test time. The high-speed M9111A can change its output voltage, stabilize that voltage, and accurately measure current from Amps down to micro-Amps all in less than 1 ms so that you can move on to the next test as quickly as possible.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Sealed Electrochemical Cell [10ml-500ml]
FPS-2
-
FPS-2 Sealed Electrochemical Cell [10ml-500ml] is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model.
-
Product
Multi-Channel Data Acquisition System
PI-3105
-
This highly flexible system is designed to test a wide variety of imaging devices, from low-noise astronomy and medical devices, to military and machine-vision devices with GB/sec data rates.
-
Product
Electronic Safe & Arm Devices
-
Excelitas Technologies specializes in the design, manufacture, and testing of MIL-STD-1316 compliant Electronic Safe and Arm Devices (ESAD), Electronic Safe, Arm and Fire Devices (ESAF), and Firing Modules (FM) for safe fuzing requirements of both legacy and next-generation missiles and munitions. Our dedicated staff of research and design experts use the latest advances in technology to design smaller, lighter, and more cost effective ESAFs and FMs to meet evolving requirements of newer more sophisticated weapon systems. Capabilities include a line of components and subsystems that have been qualified for hard target penetration environments and next-generation smaller-class munitions.
-
Product
Radio Frequency (RF) Generators
-
Find and fix design problems during developmental testing. Viasat’s RF signal environment generation surpasses ordinary simulation and computer modeling techniques to deliver a true-to-life, dense avionics environment for the most accurate analysis of RF communication system performance.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm
40-294-022
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
300 HP Complete Bench Hydraulic Test Center
HTC-300
-
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 300 hp (224 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators). The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
Product
Aerial Lift Testers
ALT Series
-
HVI produces AC voltage testers that perform boom and liner testing, with models available up to 300 kV AC for boom testing and 10 kVA for liner testing. The ALT Series is designed for AC voltage testing aerial lift devices. The standard models available are rated 120/60 kV AC, 200 kV AC, and 300 kV AC, rated up to 7 kVA.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
Plug-in Modules for High-Performance Testing
D Series
-
With the invention of the D Series line, Introspect Technology has revolutionized the way product engineers test high-speed digital applications. Our unique plug-in module design allows for high-performance testing on any load board and eliminates the need for cables. Despite the continuous transformation of the test industry in recent years, a growing number of legacy equipment remain in use.
-
Product
Relay Test Set Type SP-I
-
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
Product
50Hz-100kHz LCR Meter
Chroma 11022/11025
-
Chroma Systems Solutions, Inc.
The Chroma 11022 and 11025 LCR Meters are passive component testers that can give you the most cost effective alternative equivalent to the high priced meters. They are designed for the demanding applications in production test, incoming inspection, component design and evaluation. Programmable test signal level settings are from10mV to 1V in a step of 10mV, and the VM/IM signal level monitor functions allow you to evaluate your devices at the level you specify. Ten test frequencies of 50Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, and 100kHz, can be used to evaluate passive components and transformers/ LF coils.
-
Product
200 HP Complete Bench Hydraulic Tester Center
HTC-200
-
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 200 hp (149 kW) Complete Bench is for the dealer that services components from a predominately small to medium size machine mix such as small construction equipment (tractors, loaders, small excavators and dozers). The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closedloop pumps.
-
Product
Complete IP Module
Scan Ring Linker SRL
-
The Scan Ring Linker SRLTM - is a complete IP module that can be easily embedded into a CPLD, FPGA or ASIC on a PCB to reduce the complexities and costs of designing 1149.1 (JTAG) test infrastructure for designs that use multiple scan rings. The SRL IP module links any number of scan rings (secondary scan paths) into a single high-speed test bus, which permits devices on secondary scan chains to be independently tested and configured through a single 1149.1 external interface.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm With SPDT
50-293-112
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Multifunction I/O Module
Multifunction I/O
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Digital Battery Testers
-
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
Product
Reach-In Altitude Test Chamber
-
Weiber Altitude Test Chamber combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 10,400 meters (25kPa). Altitude testing may be continued without temperature control up to 600,000 meters (0.1 kPa).High Low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. Two common applications of High Low Humidity Altitude Test Chamber are testing of avionics or other aerospace equipment to simulate actual conditions, and simulate high-altitude conditions found in mountainous regions or other regions. All models are factory tested, with an ergonomic and maintenance cum user-friendly design. These CE approved test chambers are created with multi-layered insulation with double vapour barrier is of low 'K' factor, high density and of non-hygroscopic in nature. Weiber test chamber are made in accordance with the international standard. Weiber Test Chambers are GMP complaints and are also ISO and NABL certified.
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
MLDD 8-Way Power Dividers
-
KRYTAR MLDD 8-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR’s power dividers offer the widest frequency coverage in a single package on the market and provides superior performance. Targeting broadband electronic warfare (EW) systems and complex switch-matrix applications, for example, KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 8-way power dividers can also be manufactured to meet military specifications.
-
Product
Goniophotometer Test System For Led Lamp
LCG-1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
Electrical Testing & Repair Kit
520
-
Thexton Manufacturing Company, Inc.
This Electrical Testing & Circuit Repair Kit is designed to test and replace defective terminals.
-
Product
HDD Motor Testers
BK8015/BK8015A
-
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
Product
The Lorlin© Impact Series
-
Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability. The system tests most all discrete semiconductors with reliable, accurate, and repeatable results.
-
Product
Software
DataPRO
-
Diversified Technical Systems, Inc.
DataPRO is a powerful set-up, control and data viewing software including ISO MME support. The modern user interface is designed to help test engineers create, control and manage every aspect of a test. DataPRO can be installed with an SQL server database and configured with individual user logins and access levels to support facilities and users of all sizes and capabilities. DataPRO works with all SLICE, TDAS G5 and TDAS PRO hardware and is required for systems using SLICE PRO TOM, DIM or TDM modules.
-
Product
Stability Walk-in Chambers
-
Stability walk-in rooms are an ESPEC North America specialty, designed for light-duty testing or long-term steady-state evaluation of pharmaceuticals and other products.
-
Product
Socket Phone
-
Design for phone device test and system verify.Phone device: CPU,flash,baseband,LPDDR,power IC.etcPitch range from 0.30 to 1.27mmKey material: PEI,Peek,Torlon,PPS.etcContact with top pogo pin
-
Product
Fax/ Modem Testing
-
To successfully deploy fax services requires extensive network design, test and traffic engineering. Test equipment can prove valuable in this process, if it can: Generate and receive fax signals in bulk over wired and wireless networks, monitor and distinguish fax signals in real time for traffic engineering and network design purposes, and analyze fax signals after capture for troubleshooting failed or poorly handled calls.
