Sun Simulators
replicate the sun's light.
-
product
Field Simulation Software
QuickField™
QuickField™ is a very efficient Finite Element Analysis package for electromagnetic, thermal, and stress design simulation with coupled multi-field analysis.
-
product
Basic Rate and Primary Rate Simulator
emutel Pro
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
MHG Solar Simulation
Atlas Material Testing Solutions
Filtered MHG lighting is a mature technology used since the 80’s for larger solar simulators inside environmental test chambers. MHG lamps are filled with a mixture of mercury, halides and rare earth elements which vaporize during ignition, generating a plasma. After a few minutes, the plasma reaches thermal equilibrium and emits a quasi-continuous spectrum (when properly filtered) similar to global solar radiation.
-
product
Environmental Simulation
Is your product heat-resistant? Throughout their useful lives, technical products are subject to a multitude of environmental influences, e.g., heat, cold, oscillations or impacts. This influences their functioning and length of service life. We can find out how the effect and cause are interrelated with an environmental simulation. We will test your products under specific environmental conditions and help you to optimize them for sustainable product development.
-
product
CAN & LIN bus Custom Test & Simulation Software
CanX
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
product
4 Channel Precision Resistance Simulator Card
DP-cPCI-2709
DP-cPCI-2709 RTD Simulator is ideal for applications of Resistance Temperature Detector(RTD) simulation requiring high resolution and low value resistances . DP-cPCI-2709 is offered in two factory selectable configurations of 4 channels and 2 channels depending on the resistance range needed. The 4 channel configuration offers resistance ranging from 30Wto 75Win steps of 50 mWresolution. This is ideal for applications where low Ohmic simulation is required. Similarly, the 2 resolution.
-
product
Solar Simulator (JIS AAA)
PEC-L12
●A compact power supply box allows installation on a desktop●The irradiation direction can be freely rotated 360 degrees●A 5cm square optical filter can be attached●Quiet shutter sound (equipped with a low-noise shutter)
-
product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
product
PXI/PXIe LVDT, RVDT, Resolver Simulator Modules
Linear variable differential transformers (LVDT) are electrical transformer sensors to measure linear displacement. Driven by an AC excitation source, the LVDT generates a pair of AC output signals modulated according to the core's mechanical position (displacement). LVDTs have been widely used in applications such as power turbines, hydraulics, automation, aircraft, satellites, nuclear reactors, and many others. These transducers have low hysteresis and excellent repeatability.
-
product
Oxygen Sensor Tester and Simulator
ST05
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
product
BRI and PRI Simulator
emutel Ultra
emutel Ultra is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Ultra can emulate different country specific networks by adding network personality cards & networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Ultra.
-
product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
8 Port Phone Line Simulator (FXS) Adv
CH-8FXS-A
This unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 2-Banks
43-670-003-AABBCC
The 41/43-670-003 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
product
Precision RTD Simulator
RTD Series
The RTD Series Precision RTD (Resistance Temperature Detector) Simulator provides a very broad-range of absolute resistance values that replace RTD's and thermocouples. Thermocouples present a resistance that depends on the temperature. The RTD simulator effectively replaces an RTD to test, analyze, and calibrate RTD measuring systems. The RTD Series simulator is a precision resistance source with excellent characteristics of accuracy, stability, temperature coefcient, and power coefcient. All these features serve to make it a laboratory resistance standard, exceeded in performance only by stand-alone standard resistors. The special design of the RTD Series provides absolute accuracy, and requires no zero resistance subtraction from any setting Special design of the RTD virtually eliminate zero resistance and switch contact variations, providing the specified absolute accuracy over the entire range.
-
product
MIMIC® IoT Simulator
The MIMIC IoT Simulator creates a real-world test lab with many thousands of manageable IoT sensors, gateways and other connected devices to simulate your IoT environment related to*Industry 4.0*Smart Factories*Smart Cities*Smart agriculture
-
product
Simulation Tool
Would you like to do code development with minimal hardware or see real-time switching and debug information? The LXI Simulation Tool can do that for you. This tool supports the simulation of all our PXI and LXI switching products, and most of the PXI simulation products in one highly portable package. The tool provides you with a simple and highly portable platform for application development.
-
product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
LOCAL LOOP SIMULATOR FOR TR-114 INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
-
product
Pulse Oximeter Simulators
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
product
OBD2/J1708/J1587 Simulator
DFLSOBD2
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
product
2 PRI + 24 BRI-U ISDN Simulator
CH-24BRI-U-MOD-2PRI
The most inexpensive ISDN simulator on the market. This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
ESD - Simulator
SESD 216
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
