Distributed Antenna System
-
Product
Standard Gain Horn Antenna
SAS-586
-
This Standard Gain Horn Antenna will provide reliable, repeatable measurements. An ideal solution and a standard workhorse of any EMC test house for compliance testing. Features: 12.4 GHz to 18 GHz, Individually Calibrated, FCC, MIL-STD, VDE and TEMPEST Testing.
-
Product
Positioning Test System
TS-LBS
Test System
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Antenna and Cable analyzers
VNA
-
Are used to analyze and fine-tune antennas and cables, measure cable parameters, and find cable faults.
-
Product
Log Periodic Antenna
ZDS7-1-6G-832
-
Log Periodic Antenna, Frequency 1~6GHz, Gain 9dBi, VSWR 2.5, Linear polarization, N-Female
-
Product
Antenna, Ridged Guide
EM-6960 | 200 MHz – 2 GHz
-
The EM-6960 operates over the 200 MHz to 2 GHz frequency range and is characterized by relatively high gain and low VSWR over this wide range.
-
Product
Loop Antennas
-
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements,
-
Product
Heat Distribution Measurement Film
Thermoscale
-
Measuring heat distribution—from points on a graph to entire surfaces.Thermoscale is a epoch-making new film that enables anyone to measure heat distribution easily by observing variations in density and hue.
-
Product
Bilogical Antenna
-
For rapid deployment along with the mobility of small package, these Bilogical Antenna Kits provides an inexpensive solution to broadband applications. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Bilogical antenna will provide reliable, repeatable measurements. The ability to sweep in one trace makes the Bilogical antenna a versatile performer.
-
Product
Logarithmic Periodic Broadband Antennas
Standard LPDA
-
Is a demountable logarithmic- periodic broadband Antenna (LPDA). For transport and space saving storage, it is delivered with fast links. The fast links allow to demount the rear elements within a few seconds without any tools.
-
Product
Indoor DAS Antenna
-
* Many of the antennas offer multi-band support: 700-2700 MHz*High front to back isolation*Omni and directional formats*Ceiling and wall mount configurations
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
Embedded Antennas
-
Embedded chip antennas are compact and integrated antennas designed to be directly mounted on a printed circuit board (PCB) or embedded within electronic devices. These antennas are often used in wireless communication applications, such as Wi-Fi, Bluetooth, GPS, and IoT devices, due to their small size and ease of integration.
-
Product
Wideband Swept Antenna, Cable Analyzer
SWR TRUE 3013
-
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
Product
VHF Radio Direction Finding Antennas
Vector-Finder Series
-
The Vector-Finder Series of VHF direction finding antennas provide a compact, lightweight, active antenna, suitable for use in the field with handheld transceivers and scanning radios. The mechanical design allows the sense antennas to be folded back to provide a compact unit, easily stowed or transported in any vehicle. The system interfaces with any FM receiver or transceiver via the antenna jack and the earphone jack. Several different models are available to suit your pocketbook or unique field application, all of which operate on the phase shift technique. The VF-142Q models incorporate left-right indicators as well as an audible response from which the user can determine the true direction of the radio signal. The other types utilize the audible response generated by the equipment and heard on the user’s receiver or transceiver. All models operate from a 9-volt battery.
-
Product
Cable And Antenna Analyzers
iVA Series
-
Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/ return loss and the location of the VSWR/return loss faults in their RF infrastructure.
-
Product
Antenna, Log Periodic
EM-6947 | 200 MHz – 5 GHz
-
The EM-6947 is an ultra-wide bandwidth log periodic dipole array aimed at applications requiring consistent performance over a very wide frequency range. Capable of both receiving and moderate power level transmitting, the EM-6947 can take the place of two or more conventional antennas, allowing you to take full advantage of the tuning range capabilities of modern receiver and spectrum analyzer designs with less inconvenience caused by the need to switch antennas.
-
Product
Shaker Systems
-
Vibration Research Corporation
Small force vibration testing equipment and shakers for product and modal analysis testing. Each system consists of a shaker and a matching linear direct-coupled power amplifier. Additional components may be added to the basic system to tailor it to your specific needs.
-
Product
Broadband Antenna
DRH2
-
Wide frequency range, ideal to complement RF test enclosures for various wireless testing applications
-
Product
Antenna, Log Periodic
EM-6944 | 200 MHz – 3 GHz
-
The EM-6944 offers an exceptional combination of frequency coverage from 200 MHz – 3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
Product
Digital Antenna Monitors
1900 Series
-
There are three different units in the 1900 Series. The basic unit is the Model 1901.This 5 1/4 inch unit contains control/measurement circuitry for up to 12 towers, digital display of all measurements, local operating controls, and an interface to a remote control system. The control/measurement circuitry for each tower is contained in a separate module. The modules plug into the rearof the unit, and may be easily added to an expanding station.
-
Product
Custom Systems
-
ORTEC strives to meet your measurement needs in every aspect. If one of our standard solutions is not the answer, we have the expertise, equipment, and commitment to design and develop robust solutions that satisfy your particular application requirements.
-
Product
Metrology System
IVS
-
The IVS 220 system is the latest generation in the IVS series and has been designed for ultimate precision, TIS (tool induced shift) and throughput on 200mm wafers. The cornerstone of the system’s reliability and stability is its mean time between failure (MTBF) of 2,100 hours. The IVS 280 provides the same capability in a package designed for overhead track handling with full E84 GEM300 capability.
-
-
Product
Etch System
-
When it comes to clean etches, Veeco’s Ion Beam Etch (IBE) systems deliver with sharp control and minimal disruption. Using a focused argon ion beam, this subtractive technique etches nanoscale features with precision, making it a go-to for pattern transfer, layer removal, and surface refinement where edge definition matters most.
-
Product
Antenna Switch
SixPak
-
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
Product
GPS/GNSS Anti-Jam Antenna
8230 AJ
-
The 8230AJ anti-jam antenna is a high gain (40 dB) GNSS outdoor antenna with a unique conical antenna pattern that rejects interference from the horizon. The antenna rejects signals at lower elevation angles – where most of the interference comes from – and only receives signals from higher elevation angles where the true satellites are. This way, you get all the performance and timing accuracy you would with a standard antenna plus 20 dB or more of interference rejection.It uses a three-stage low noise amplifier, a mid- section SAW, and a tight pre-filter to protect against saturation by high level sub-harmonics and L-band signals. The antenna covers GPS L1, GLONASS L1, BeiDou B1, Galileo E1, and QZSS L1.
-
Product
Rack Systems
-
Real-time testing and validation often require versatile testing platforms, providing a high number of different signals ranging from low-power communication and sensor signals to high-power actuator signals. Integrating all the necessary components in one standard system and designing signal-conditioning for all interfaces is time-consuming and requires specific expertise.
-
Product
Dilution-Extractive System
ML675
-
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
Product
Communication Systems
-
Tactical networking radio system comprising of transmit/receive modules, converters, synthesizer, RF switching, power supplies, controllers and an antenna array. The radio automatically selects the best communications path to create a self-forming, self-healing network.
-
Product
Survey Systems
-
Pair the Smart Chamber with a gas analyzer of your choosing and connect using your mobile device or laptop via the built-in Wi-Fi web server. See live flux data with a LI-COR gas analyzer or connect to a third-party analyzer and the chamber will log GPS and ancillary data for your flux measurements.
