Distributed Antenna System
-
Product
Battery Test Systems
-
Was designed to meet the specific demands of our loyal customers. This system is used to test both single cell batteries as well as super-capacitors.
-
Product
Quantum Efficiency Measurement Systems
-
Newest generation of quantum efficiency (yield) measurement tool, which allows the user to determine QE of powders, liquids, solids and films. An optically optimized geometry using an integration hemisphere and low stray light array spectrometer enables world class measurements and new applications.
-
Product
Wafer Flatness Measurement System
FLA-200
-
*Measures Thickness, TTV, Bow, Warp and site and global Flatness (ASTM compliance)*Measures all materials including Si, GaAs, Ge, InP, SiC*Full 500 micron thickness measurement range without re-*calibration2-D /3-D Mapping software
-
Product
Ground-Fault Detectors for Ungrounded Systems
-
Early detection of ground faults on ungrounded systems allows critical systems to remain online while faults are identified and resolved. By continuously monitoring the system's insulation resistance, Bender's ground-fault detectors can provide early indication of both immediate and trending ground faults before leakage current may be of concern.
-
Product
Data Acquisition System
Synergy Qb
-
The Synergy Qb offers the same Synergy input capabilities in a field rugged product offering IP51 environmental resistance against dust and water. This DC-operated system can acquire standalone to its internal low-power PC with solid state drive, or to an external PC via Ethernet.
-
Product
Modular Battery Test System
-
This modular battery test system provides for manufacturers versatile testing possibilities. Due to modularity it allows easy configuration of battery testers for a wide range of different power levels.
-
Product
Commercial Test Systems
-
IR Target Projectors, IR/Visible Target Projections, Wide FOV Target Projectors, Focal Plane Array Tester, Fused IR/Visible Projectors, High Volume Tester, IR/Visible Ranging Projectors, Dual Blackbody Wide FOV, Future Test Requirements.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
Shaker Systems
-
Vibration Research Corporation
Small force vibration testing equipment and shakers for product and modal analysis testing. Each system consists of a shaker and a matching linear direct-coupled power amplifier. Additional components may be added to the basic system to tailor it to your specific needs.
-
Product
Standard Gain Horn Conical Lens antennas
-
Elva’s SLHA series of standard gain horn lens antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.
-
Product
Radio System
FASST
-
Futaba is the first of the traditional radio manufacturers to bring the advantages of 2.4GHz spread spectrum technology to modelers – and the first to introduce that technology in a full-range aircraft system. For getting the full benefits of 2.4GHz technology, you'll find that Futaba's experience makes all the difference.
-
Product
Antennas
-
LSR is unmatched in offering multiple pre-certified antenna options for each wireless module. Pairing LSR’s embedded modules with a pre-certified RF antenna saves both certification time and costs. The new, exclusive, flexible antenna solutions from LSR, provide unmatched flexibility to help you solve your real-world design challenges. Learn more about the FlexPIFA™, mFlexPIFA™, and FlexNotch™ antennas from LSR and how they can provide design freedoms you didn’t know were possible.
-
Product
Vibration Test Systems
-
L.A.B.’s Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration.
-
Product
AirTech Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Hillger NDT has developed AirTech testing technology for the requirements of air-coupled testing. Our USPC 4000 AirTech ultrasonic testing system and our robust AirTech sensors consisting of optimized transmit and receive probes deliver optimal results under demanding conditions.
-
Product
Automated Systems
-
The Rice Lake line of automated systems gives your system the efficiency it needs to keep up with growing business.
-
Product
Ground Grid Systems
-
The Ground Grid systems module enables engineers to quickly and accurately design and analyze ground protection. Flexible design methodologies allow for quick auto-designed layouts or very detailed schemes. Color-coded graphical plots provide impressive results.
-
Product
Torque Metering System
-
Measure and record torque for rotating machinery, test stands and ship board applications. Riverhawk Torque Meter Systems are capable of retrofitting to existing couplings and shafts with minimal modification.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Systems Analysis Interface
Saint2
-
The Systems Analysis INterface Tool 2, a Delphi Preferred Tool, for Low-cost EOL Testing & Reflashing Without the Need of Additional Hardware.
-
Product
Measuring Systems For Beverage Can Manufacture
RICOS - Specialized Ring Contour Gauge For Drawing Dies
-
Optik Elektronik Gerätetechnik GmbH
Special designed for measurement of inside profile (land angles) of ironing dies for 2-piece beverage can manufacture, tolerance model and comparison with CAD data. Measuring task of RICOS is the measurement and evaluation of the inside profile of ironing rings in beverage can manufacture The measuring and evaluation system RICOS serve the profile measurement and the tolerance evaluation of ironing rings for beverage can manufacture.
-
Product
Image Sensor Characterization Systems
-
Image Sensor QE and Spectral Responsivity Characterization
-
Product
CNC Vision Measuring System
Quick Vision Active Series
-
The Quick Vision Series comprises a family of CNC precision measuring machines equipped with an optical unit on which an image sensor is mounted. Non-contact measurement is performed by computer-processing the workpiece images. Since the first release in 1993, this series has been used in various industries including electrical and electronic, medical equipment and pharmaceutical, automotive, and machine parts, to name just a few. Mitutoyo has significantly contributed to quality and productivity improvements for those customers who use our CNC Vision Measuring Systems in measurement of precision parts on their production lines, especially when incorporated in semi-automatic inspection systems.
-
Product
High Speed Camera Systems
MEMRECAM MX
-
The nac MEMRECAM MX is a robust, turnkey solution for multi-camera onboard and offboard automotive testing and occupant safety applications. Each system supports up to eight, tightly synchronized camera views, and integrates seamlessly with all current and legacy MEMRECAM imaging systems.
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
-
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
-
Product
MMIs for Test and System Integration
-
Laying out a custom PCB is too time consuming and costly for most rush projects. Pulse Research Lab has developed Mini Modular Instruments ™ to provide cost effective solutions to the most common engineering challenges.
-
Product
Environment Monitoring System
ENVIROMUX-2D
-
The ENVIROMUX-2D supports 2 external configurable sensors, 5 digital inputs, and 1 output relay for control of external devices. It features 2 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
-
Product
Burn-In System
-
The COBIS-II Series Burn-in System is designed to test the latest high frequency integrated circuits (ICs) and combines a large capacity oven with well proven Accutron FlexBID™ dynamic driver technology. This system is engineered for productive dynamic device testing and reliable monitoring.
-
Product
Measurement System for ESD Protection
SampleProtect
-
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
Product
Remote I/O Systems
-
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.
