Wave Solder
-
Product
Soldering Station
SM-898D
-
*Using micro-processor PID program control technology, precise dual digital display hot air gun and the stability of the actual temperature of the soldering iron, fast automatic temperature compensation feature further enhanced temperatures.*The amount of wind, air flow, temperature soldering iron are adjustable.*The air gun holder is a magnetron (or light control), holding the handle when the system will automatically enter the working mode; handle is placed on the shelf when the system enters standby mode automatically.(One more than the 898D Auto Sleep off function)*System with automatic cold wind function, can prolong the life of the heating element.*This product uses "brushless fan" as a source of air, reduce noise, improve work efficiency
-
Product
VDI Erickson PM5B MM–Wave Power Meter with W-Band Sensor, Optional Tapers to 1.5 THz
N1913PM5B
Power Meter
N1913PM5B is a Virginia Diodes, Inc./Erickson PM5B calorimetric mm-wave power meter, with a W-Band sensor for power measurement over a frequency range of 75-110 GHz.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
Amplifier
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
Product
Replacement Solder tip lead set for D420/D620
Dx20-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
01 With Soldering Eyelets | 10 Positions | M10
01-1xxx-00/30xx-10-N
-
Multi wafer compact selector with 36° detent angle, 6 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
3D Inline Solder Paste Inspection System
TROI 7700 SERIES
-
Using Moire' pattern, Pemtron's three-dimensional lead applicationdosage tester combines 2D color images with 3D measurement data toprovide more detailed, near-real PCB images, unlike traditionalcolor maps. We will also provide you with the best solution forhigh-quality and high-precision PCB production with a varietyof statistical programs, along with information you need toquickly and accurately judge positive/failure.
-
Product
01 With Soldering Eyelets | 12 Positions | M6
01-1xxx-00/30xx-12-M
-
Multi wafer compact selector with 30° detent angle, 3 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
3D Solder Paste Inspection (SPI)
-
Systems designed for solder paste inspection (SPI) quickly and reliably check the solder paste deposits on the circuit board.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Guided Wave Radar Level Transmitters
LWT Series
-
For high-accuracy, reliable measurements even in harsh conditions.Using radar frequencies, guided in a probe going into the monitored vessel, guided-wave radar level measurement provides continuous, reliable measurements with high accuracy. The radar wave being guided by the probe, the wave energy remains high which allows measurement even in harsh conditions.
-
Product
SparkFun Solder-able Breadboard
-
This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Single Photon Detector System For Near-Infrared (1.6-2.3 Um Wavelength) Waves With Liquid Helium (LHe) Cryostat
-
Insight Product Company is proud to offer Single Photon Detector System for Near-Infrared (1.6-2.3 um wavelength) with Liquid Helium (LHe) Cryostat. Insight Product Co. offers superconducting single photon detectors and ultra-low noise registration systems for the near infrared range. All systems operate in continuous mode, no gating required.
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
Amplifier
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
Product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
-
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
Product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
40-960-104-M
D-Sub Male Connector
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell.
-
Product
Lo-PRO®file Collet Socket with Solder Tail Pins
Series 513
-
LO-PROfile Collet Sockets with Solder Tail Pins. Features: LO-PRO file Collet Sockets are available with solder tail or wire wrap pins. Consult Data Sheet No. 12012 for wire wrap pins. Choose from several size and plating options
-
Product
HD Arbitrary Waveform Generator, 2 Ch, 250 MHz, 16 bit, 128Mpts/Ch, 6 Vpp output, Wave Sequencing
T3AWG3252
Arbitrary Waveform Generator
HD Arbitrary Waveform Generator, 2 Ch, 250 MHz, 16 bit, 128Mpts/Ch, 6 Vpp output, Wave Sequencing.
-
Product
Millimeter Wave Zero Bias GaAs Schottky Diode
HSCH-9161
Diode Detector
The HSCH-9161 is suitable for medium-low barrier, zero bias detector applications. The HSCH-9161 is functional through W-band (110 GHz) and can be mounted in microstrip, finline, and coplanar circuits.
-
Product
Replacement Solder Tip Leadset for Use with D420/620
Dx20-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
-
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
Product
Normal Incidence Shear Wave Transducers
-
Single element normal incidence Shear Wave Transducers contact transducers introduce shear waves directly into the test piece without the use of refracted wave mode conversion. We recommend the use of our SWC shear wave couplant for general purpose testing.
-
Product
Guided Wave Radar
-
A top-down, direct sensing technology that uses low-energy microwave pulses sent down a probe to accurately detect the boundary between two immiscible liquids.
-
Product
01 With Soldering Eyelets | 10 Positions | M6
01-1xxx-00/30xxx-10-M
-
Multi wafer compact selector with 36° detent angle, 3 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
01 With Soldering Eyelets | 12 Positions | M10
01-1xxx-00/30xx-12-N
-
Multi wafer compact selector with 30° detent angle, 6 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
D-Sub Female Connector
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
Guided Wave Radar Sensors
LVRD10 Series
-
The LVRD10 Series guided wave radar transmitters provide continuous level measurement with a 4 to 20 mA signal output. Offered in single rod, coaxial, or weight & cable probes in 3 or 6 foot lengths
-
Product
Open-Frame Collet Socket with Solder Tail Pins
Series 518
-
Open Frame Collet Sockets with Solder Tail Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. Choose from several pin styles. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
