Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
Product
Fatigue Rated Low Profile Cells
-
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
Product
Quadrature Position & Rate Meter
-
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
Product
Error Proofing Applications
-
ARC has assisted in Error Proofing critical processes at many companies like yours, to implement visual based process verification, data-centric process flow and, if needed, connected tooling that can be combined to improve your operation. By providing a process verification system that can be connected into your manual and automated processes, you can achieve your error proofing goals.
-
Product
Walk in Chamber for Rapid Rate Temperature / Humidity Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Chamber for Rapid Rate Temperature / Humidity Test Relevant standards requirement:Temperature shockTest Object: Battery storage pack or system.Li-ion battery pack or system placed in (-40±2)℃~(85±2)℃ alternation temperature, the conversion time of two extreme temperatures is less than 30 minutes. Place the test objects into each extreme temperature keep 8h, test 5 cycles.Observe for 2 hours under the room temperature after testing,Humidity & Temperature CyclingTest Object: Battery storage pack or system.Refer the GB/T2423.4 Test Db, variable refer the Graph 4,the highest temperature is +80℃,5 cycles. Observe for 2h under the room temperature.
-
Product
Gearbox Tester
-
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
8FE M12 Unmanaged Ethernet Switch, IP67 Rating
EKI-2528I-M12
-
M12 Connectors and IP67 housing, Provides 8 fast Ethernet ports with Auto MDI/MDI-X. Supports 10/100 Mbps auto-negotiation, Complies with IEC 61131-2 specifications. Supports redundant 12 ~ 48 VDC power input, Supports wide operating temperature range from -40 to 75 °C.
-
Product
Quick Dry Rate Tester
-
Sataton Instruments Technology CO., Ltd
Quick dry rate tester is professional designed to determine the dry rate of fabric, which is exposed to a prescribed volume of water, tested surface temperature change, and time of drying. The tester is based on the heated plate method to determine the dry rate. It is applicable to all types of fabrics, including knits, wovens, and non-wovens, as well as to fabrics taken from end product items.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
Integrated Receivers/Demodulators/Bit Synchronizers
-
Lumistar provides a wide variety of rack mount integrated receiver and diversity combiner systems. Some of these can be configured with multiple receivers, diversity combiners, and bit synchronizers depending on custom requirements. Lumistar does not manufacture any computers, but selects only the finest of the industrial machines available to provide a high performance package. Basic system setup, control, and display software is included with each of these systems at no additional cost.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
-
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Run-Time Error Analyzer
Astrée
-
AbsInt Angewandte Informatik GmbH
Astre analyzes structured C programs with complex memory usages, but without recursion or dynamic memory allocation. This targets embedded applications as found in earth transportation, nuclear energy, medical instrumentation, aeronautics and space flight, in particular synchronous control/command such as electric flight control.
-
Product
Digital Bit Pattern Generator
FAB-3226
-
The FAB-3226 Digital Bit Pattern Generator connects digital ports to an user-defined FPGA logic. As the FPGA is user-programmable all kind of operation can be implemented: input, output, and closed loop operation where input and output are processed in real-time. All this can be controlled by an user-defined application program running on a computer system (PC or embedded).
-
Product
Frequency, Rate Meter, Flow Rate Indicator
-
Two independent scalable pulse-input channels from 0 Hz to 1 MHz. Channels may be combined arithmetically. One channel can display total while other displays rate. High read rate for control applications: AC line frequency can be measured to 50.0000 or 60.0000 Hz in a few line cycles. Ideal for use as a tachometer or readout of a turbine flow meter.
-
Product
Ultra Fast Digitizer With 8 Bit, 4 GS/s Sampling Rate With Up To 8 GS Memory
CompuScope Express 14G8
-
The CobraMax CompuScope family of GaGe ultra high-speed 8-bit digitizers provides the most powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features on a single PCI Express or PCI card.
-
Product
SparkFun Pulse Oximeter And Heart Rate Sensor
MAX30101 & MAX32664 (Qwiic)
-
The SparkFun Pulse Oximeter and Heart Rate Sensor is an I2C based biometric sensor, utilizing two chips from Maxim Integrated: the MAX32664 Biometric Sensor Hub and the MAX30101 Pulse Oximetry and Heart Rate Module. While the latter does all the sensing, the former is an incredibly small and fast Cortex M4 processor that handles all of the algorithmic calculations, digital filtering, pressure/position compensation, advanced R-wave detection, and automatic gain control. We've provided a Qwiic connector to easily connect to the I2C data lines but you will also need to connect to two additional lines. This board is very small, measuring at 1in x 0.5in (25.4mm x 12.7mm), which means it will fit nicely on your finger without all the bulk.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
-
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Defibrillator Analyzers, Pacemaker Testers and AED Testers
-
Fluke Biomedical’s defibrillator analyzers and defibrillator/transcutaneous pacemaker testing devices are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment. We offer best-in-class defibrillator testers that feature capabilities which encompass a wide spectrum of worldwide established pulse shapes, showcasing AED tester compatibility, and outperforming competitors in accuracy and standards.
-
Product
Electrical Tester
PRO T6-1000
-
The T6-1000 PRO Electrical Tester measures voltage up to 1000 V ac and current up to 200 A ac, all through the open fork and without test lead contact to live voltage. Connect the black lead to ground with the included heavy-duty alligator clip, slide the wire into the open fork and see both voltage and current at the same time. On wires up to AWG 4/0 (120 mm2), carrying as much as 200 A and 1000 V ac. Even with gloves on. It will change how you do your job.
-
Product
Voltage Testers
-
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
Product
Static Tester
-
Electrostate tester with LED indicator for the detection of static charge in the plus and minus range. An indispensable, inexpensive tool for the assessment and selection of materials in the living area, as well as the quality of the room climate.Buy Data Sheet
-
Product
Rebuilt Testers
-
Lorlin® manufacturers New and Rebuilt Discrete Component Semiconductor Test Systems for Transistors, Diodes, Zeners, Fets, IGBTs, SCRs, Triacs, Optos, Small Signal and Power Semiconductors. We measure, screen, test, analyze, characterize and sort the critical parameters of semiconductors devices including Leakage Current, Breakdown Voltage, Gain, Saturation Voltages, and offer a comprehensive test parameter library with an easy to use Windows based applications software. The systems us a Windows 10® 64-BIT Operating System with a USB 2.0 Interface. Engineering excellence, innovation, creativity and cutting edge technology has made Lorlin equipment well known for testing discrete components.
-
Product
Multifunction Tester
FULLTEST3
-
Multifunction Tester for safety of machinery IEC/EN60204-1:2016 and low voltage switchgears and controlgears IEC/EN61439-1-2:2011
-
Product
Diode Tester
FEC200E
-
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
Product
HIPOT testers
HypotMAX III
-
Patented SmartGFI® functionStorage of 50 test setupsRemote Safety InterlockUSB/RS-232 or GPIB interfaces availableAdvanced menu driven controlDigitally controlled arc detection systemCHARGE LO® & RAMP HI® systems
-
Product
Electrical Testers & Voltage Continuity Testers
-
Fluke’s line of electrical testers and voltage detectors are designed for use in every application and in nearly any environment. From non-contact voltage detectors and voltage testers with continuity detectors, to open-jaw current testers and open fork testers with FieldSense® technology (for voltage and current measurements without test leads), these testers are accurate, safe and easy to use.
-
Product
Electrical Tester
T6-1000
-
The Fluke T6-1000 Electrical Tester with FieldSense™ technology lets you quickly, safely take True rms voltage and current measurements without test leads.
-
Product
Adhesion Tester
-
An adhesion tester measures the force required to detach a coating from a substrate. Often called a pull-off adhesion tester or peel tester, an adhesion tester applies a large amount of force to evaluate a coating's bond strength. When measuring peel force or adhesiveness, the nature of the substrate's surface plays a significant role. However, a high-quality adhesion tester features a self-aligning measuring head to compensate for any surface irregularities.
-
Product
Tester & Programmer
TP-TACT
-
TP-TACT is designed to test the efficiency and program the operating range of electronic turbocharger controllers.
-
Product
Hipot Tester
ET 2670 A
-
REOO ET 2670 A Solar Module Testing Machine is designed for PV module manufacturing inspection, enabling faster defect judgment and more stable quality verification during production. Built for solar factories, it supports reliable inspection flow.
