Model
construction of a concept.
See Also: Modeling, Modelling, Modelers, Human Body Model, Charged Device Model
-
Product
Wind Meter Base Model
Kestrel 1000
-
The Kestrel 1000 Wind Meter is the base model in our extensive assortment of Kestrel pocket weather meters. Simple and compact, the Kestrel 1000 fits right into the palm of your hand and weighs a mere 65 grams. It's also extremely durable and totally waterproof, allowing you to measure wind speeds in even the harshest weather conditions. It even floats.
-
Product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
-
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
Product
Model Quality Assurance (MQA)
-
Model Quality Assurance (MQA) is an automated SPICE model validation software which allows you to check and analyze SPICE model library, compare different models, and generate quality assurance (QA) reports in a complete and efficient way. With more than ten years of history, MQA has become the industry standard for SPICE model acceptance and signoff and is widely adopted by leading integrated device manufacturers (IDMs), foundries and design houses.
-
Product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
-
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
Product
Model Based Testing Platform
TestCast MBT
-
TestCast MBT uses an approach call model based testing (MBT) to drastically reduce the efforts required for test maintenance by generation of test cases from a behavioural model.
-
Product
Model L: Lumber Moisture Meter
MRC003303
-
Calibrated for 77 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 3/4" penetration. Rechargeable battery.
-
Product
PathWave IC-CAP PSP Model Extraction Package
W7021E
-
The W7021E PathWave IC-CAP PSP Model Extraction Package provides measurement and extraction procedures for PSP, a CMC industry-standard model advanced surface potential model for MOSFET devices.
-
Product
Simulation and Model-Based Design
Simulink
-
Simulink is a block diagram environment for multidomain simulation and Model-Based Design. It supports system-level design, simulation, automatic code generation, and continuous test and verification of embedded systems. Simulink provides a graphical editor, customizable block libraries, and solvers for modeling and simulating dynamic systems. It is integrated with MATLAB, enabling you to incorporate MATLAB algorithms into models and export simulation results to MATLAB for further analysis.
-
-
Product
Acceptance and Model Office Testing
-
Business Acceptance Testing (BAT), (also known as User Acceptance Testing UAT), is the test phase where the business owners or clients of the software test the solution to verify that deliverables meet the original business requirements. A number of reoccurring issues can present during these finals stages and experienced resources can prove invaluable during these times.
-
Product
Model A8-AF: Radome Moisture Meter
MRC005574
-
Indicates the moisture pockets in aircraft radomes. Two main components include the electrode sensor and the metering unit. Critical to today's sophisticated radar transmissions as poorly monitored moisture levels can degrade radar operation.
-
Product
Model Vector Network Analyzer
DZV-1
-
Digital Signal Technology, Inc.
DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.
-
Product
Stability Testing Chamber - Double Door Model
Q20
-
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c and corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
Product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
-
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
Product
PathWave IC-CAP BSIM4 Model Extraction Package
W7025E
-
The W7025E PathWave IC-CAP BSIM4 Model Extraction Package provides measurement and extraction procedures for the BSIM4 industry-standard model for MOSFET devices.
-
Product
Digital Power Meter (High Accuracy Model)
LS2050
-
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Product
Signature Model Surge Testers
SP
-
Surge / DC Hi-Pot testing capabilities. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope plus a DC Hi-Pot Tester. DC Hi-Pot testing with dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip. This dual tester combo is still capable of testing 3 phase motors with or without rotors.
-
Product
Economy Model Vertisocket™
Series 800 and 822
-
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
-
Product
Model Based Testing
RTT-MBT
-
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
Product
SPICE circuits & model Debugger / Analyzer
SpiceVision PRO
-
SpiceVision PRO takes the complex SPICE descriptions produced by many EDA tools and generates clean, easy-to-read transistorlevel schematics and circuit fragments, and design documentation to speed up debugging and project development.
-
Product
Stability Testing Chamber - Single Door Model
Q40
-
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
Product
Magnetic Measurement System
Model 110
-
The Model 110 Magnetic Measurement System is a very high field version of our industry-standard MESA, designed specifically to measure high-coercivity samples. It uses powerful amplifiers and specially designed water-cooled solenoid assemblies to achieve the magnetic fields required by state-of-the-art material.
-
Product
Dial Durometer
Model 1600
-
he Model 1600 features a full-sized dial face for readability to within 1/2 point. The Model 1600 offers the maximum accuracy available in a dial model gauge at a minimum cost. Available ASTM Types: A, D, B, C, DO, E, M, O, OO, OOO, OOO-S, RR and CF
-
Product
Exposure Systems
Model 2000AF & 2000SM
-
The OAI Model 2000 Exposure Systems may be configured as either an edge-bead exposure system (2000SM) or a flood exposure system (2000AF); both configurations are based on OAI’s proven, time-tested platform.
-
Product
DUV Mask Aligner
Model 200E
-
OAI’S Model 200E DUV Mask Aligner performs all the functions of the tabletop Model 200 Mask Aligner but utilizes a 185nm Excimer Lamp as the UV light source. It is used for Biotechnology Processing.
-
Product
Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System
RT-3000/RG-1000F
-
*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software
-
Product
Wide Measurement Range Model Of Semi-automatic 4 Point Probe Sheet Resistance/resistivity Measurement
RT-3000/RG-2000 (RG-3000)
-
*User programable measurement pattern & programmable measuring pattern*Tester self-test function, wide measuring range*Thickness, edge, temperature correction for silicon wafer*Film thickness conversion function from sheet resistance*2 types measuring tester (S version: Standard type, H version: High range resistivity measurement type)
-
Product
Splashproof Cover
Model IPC
-
Model IPC Splashproof Cover adds protection to IP67 / NEMA-4X from the front panel. It fits all of Laurel's 1/8 DIN instruments as well as 1/8 DIN instruments by other manufacturers, provided that instrument dimensions in front of the panel do not exceed 48 x 96 x 15 mm (1.89" x 3.78" x 0.59").
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - PCIe
Model 78141
-
Model 78141 is a member of the JadeTM family of high-performance PCIe boards. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power andcost, while still providing some of the highest-performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deployingFPGA-based data acquisition and processing. The 78141 is a high-speed analog-to-digital and digital-to-analog converter with programmable DDCs (digital downconverters) and DUCs (digital upconverters). It is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and generator features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
