Product

Resistivity Cell For N1413 (26/50 Mm Electrodes)

N1424B

-

Keysight Technologies

N1424B - Keysight Technologies

The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.

Product

ITO (Indium Tin Oxide) Electrode

-

ALS Co., Ltd

ALS Co., Ltd

This quite unique material transmits only visible light whereas it does not transmit UV radiation. Our ITO electrodes consist of 100 nm thick of ITO layer deposited on quartz or borosilicate glass substrate (0.5 mm thick).

Product

Adapter, 1.0 mm (m) to 1.85 mm (m), DC to 67 GHz

11921E

-

Keysight Technologies

11921E - Keysight Technologies

The Keysight 11921E precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.

Product

Electronic Calibration Module (ECal), 50 GHz, 2.4 Mm, 2-port

N4693D

-

Keysight Technologies

N4693D - Keysight Technologies

The Keysight N4693D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy, and accurate. The N4693D is a precision 2-port ECal module that supports 2.4 mm connectors up to 50 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4693D is included for securing your ECal module and accessories.

Product

Manual Test Solution

Titan

-

PurePulse ESD

Titan - PurePulse ESD

Titan is an easy to use, low cost Human Body Model (HBM) or Machine Model (MM) manual test solution. It can be used for design, engineering, and characterization of your devices. Ranging from 50 V to 16,000 V the Titan will have the largest voltage range of any HBM tester.

Product

WAVEPULSER-40IX + WAVEPULSER-SI-STUDIO-NRZ + Adaptors and Calibration Kit

WAVEPULSER-40iX-BUNDLE

-

Teledyne LeCroy

WAVEPULSER-40iX-BUNDLE - Teledyne LeCroy

High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables, bundle.

Product

ARM 9 System on Module

MS 1515

-

Meltronics Systemtech

MS 1515 - Meltronics Systemtech

- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high

Product

Specialized Beam Profiler Systems

-

DataRay Inc.

DataRay Inc.

DataRay offers specialized beam profiler systems. These systems offer solutions for complex applications. The large beam profiling system is suitable for beams up to 200 mm image area, and the line laser profiling system provides for direct measurement of line lasers up to 200 mm in length.

Product

Rectangular Horn Antennas

-

ERAVANT

ERAVANT

SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.

Product

Optical Visual Fault Locator

SAT-3C01

-

Shaanxi Aitelong Technology Co., Ltd

SAT-3C01 - Shaanxi Aitelong Technology Co., Ltd

SAT-3C01 Optical Visual Fault Locator is used for optical identification, fault locating of SM fiber or MM fiber, which is a basic maintenance tool of optical network, LAN, FDDI, ATM optical system, and telecom network system, suitable for field working.

Product

Metal Cored PCB

-

Teledyne Labtech

Teledyne Labtech

Teledyne Labtech is at the forefront of complex metal-cored PCB design and manufacture. The PCB use a thin metal core <2 mm, which acts as isolation between the RF/Microwave circuit and the Analogue/Digital circuitry and creates an excellent thermal path.The major advantages are reduced size and no need for complex microwave feed-thru's. The ability to laser cut pockets allows the designer engineer to mount the high power MMIC directly on to the metal core.