Unmanned Aerial System
remotely piloted sensory aircraft.
-
Product
Semiconductor Test Software
-
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
-
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Regenerative Battery Pack Test System
17020
-
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Battery Management Systems Testing
-
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
Product
CATR Benchtop Antenna Test System
ATS800B
-
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
Positioning Test System
TS-LBS
-
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Emergency Systems
-
Safety and survival products which aid in on-board emergencies, aircraft evacuation, and search and rescue operations.
-
Product
BMS Manufacturing Test System
-
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
SAS Protocol Test System
Sierra M124A
-
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
Edge AI Inference System
AIR-020R
-
Edge AI Inference system powered by NVIDIA® Jetson Orin™ Nano and Super mode. Compact and performance AI box design. NVIDIA® Jetson Orin™ Nano 8GB/4GB built-in.
-
Product
CPE Design Verification System
Jupiter 310
-
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
Electrification Testing Solutions
-
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
Product
VME Data Acquistion System
ADM-31
-
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
Edge AI HPC System
AIR-500D
-
Edge AI HPC system powered by Intel® Xeon® D-1700 Series processors with support for up to 4 PCIe slots. Intel® Xeon® D-1700 series processor 4x DDR4 SO-DIMM sockets support ECC/nonECC memory up to 128GB.
-
Product
Memory Test System
T5230
-
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
19” Rackmount Data Collection System
DCS-211
-
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
Product
Conformance Test System
TS8980
-
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
Eagle Test Systems
ETS-200T
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Mezzanine System Carrier
MMS6245
-
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
Product
Custom Test System Solutions
-
No time to think about test? One-size-fits-all testers not ideal? Existing solution no longer fits your needs? Then count on integrated test solutions from Astronics. We’ll assist you with your test strategy and your test system, setting you on the path to market at a pace and ROI that ensures your program success.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
-
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Bloomy Simulation Reference System
-
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
ESD Test System
58154 Series
-
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
Product
OLED Lifetime Test System
58131
-
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
Product
AIM System Solutions
-
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
Product
SSD Test Systems
-
Enables Rapid SSD Development and Production Ramp with Flexible Test Solution In the high-growth and highly competitive SSD market, a test system that supports multiple protocols can eliminate the need for retooling and achieve faster transitions from one product version — or one product generation — to the next. Advantest SSD Test System allows manufacturers to rapidly grow their product portfolios while remaining adaptable to the many changing needs of the evolving SSD market. This tester improves users’ engineering efficiency with powerful, easy-to-use software tools and a revolutionary multi-protocol hardware architecture, enabling accelerated SSD product development and a faster time-to-manufacturing ramp.
-
Product
Checkpoint Security System
ConneCT
-
The ConneCTTM Checkpoint Security System is an advanced aviation security explosive detection system (EDS) engineered to deliver superior threat detection, dramatically improved passenger throughput, and low total cost of ownership.
-
Product
Laser Diode Burn-in Reliability Test System
58604
-
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
