Synchronous Ethernet
ITU-T standard governing timing node to node through the physcial layer interface.
-
Product
cDAQ-9184, 4‑Slot, Ethernet CompactDAQ Chassis
782069-01
Chassis
4‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9184 is a CompactDAQ Ethernet chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. With multiple timing engines, you can run seven hardware‑timed operations simultaneously, with three independent rates for analog input.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
System of High-Speed Synchronous Registration of Analog, Digital, and Video Signals
-
The system uses a high-performance NI CompactRIO controller to simultaneously register 24 analog signals, receive an accurate digital pulse from GPS and synchronize measurements.The video signal is recorded using a high-speed camera connected to an NI PCIe-1433 frame grabber. The information received from the camera and the recording device is transmitted to a server built on the basis of an industrial computer, which writes data to an external 12-disk RAID array. The stream of recorded data in the system can reach 600 MB per second.
-
Product
Ethernet to GPIB Controller
Model 8065
-
* Controls GPIB Devices anywhere there is a network or internet connection.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* VXI-11 compliant.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver lets you change network settings from any browser.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the GPIB instruments.* 8065 is our original Ethernet to GPIB Controller and recommended for replacement purposes with existing programs. Use the Model 9065 for new applications.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for XMC
XMC-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
Dual-Port 10GBASE-T pcie Ethernet NIC
P210TP
-
The P210TP 2x10GBASE-T PCIe NIC builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
Product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
-
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
Product
Dual-Port 25GbE PCIe Ethernet NIC
P225P
-
Based on Broadcom’s scalable 10/25/50/100/200G Ethernet controller architecture, the NetXtreme®-E Series P225P 2x25G PCIe NIC is designed to build highly-scalable, feature-rich networking solutions in servers for enterprise and cloud-scale networking and storage applications, including high-performance computing, telco, machine learning, storage disaggregation, and data analytics.
-
Product
1000BASE-T1 Ethernet Logging Expansion With Low Latency
PT-20MG
-
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
Product
Cable Assy, Ethernet, Type E, Crossover, 8POS, CAT5, 10m
187375-10
Cable Assembly
8-Pin, Male Ethernet to 8-Pin, Male Ethernet, CAT-5E Crossover Ethernet Cable - The 8M-8M Crossover Cable directly connects two devices together, without the need for a router in the middle. The cable is available in different lengths.
-
Product
2-port LAN Module With Intel® X540 Ethernet Controller
AX93317
-
The AX93317 is a dual-port LAN module built with an Intel® X540 10 GbE Ethernet controller that provides acceleration technologies to optimize the processing of network data traffic, including the Intel® DPDK, SR-IOV and VMDq. The AX93317 LAN module features dual 10 GbE RJ-45 ports and a PCIe 2.0 x8 golden finger, along with a compact design adapted specifically for Axiomtek’s 1U and 2U rackmount network appliances, allowing customers to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
-
Product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
Switch Blade
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
Gigabit Ethernet
SFP Transceivers - Copper
-
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
Product
Multi-Protocol Interface for USB or Ethernet Equipped Computers
EXC-Unet2/Px
-
Multi-Protocol Interface for USB or Ethernet Equipped Computers
-
Product
Overview About LAN Ethernet Transient-Recorders / Digitizer
-
The GaGe FCiX Cobra/CobraMax LAN digitizer features 2 channels of 8-bit resolution with a maximum sampling rate up to 2 or 4 GS/s for one channel and up to 1 or 2 GS/s for two channels and true Effective Number of Bits (ENOB) up to 7.6-bits with 10 MHz input.
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
Switch Blade
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
Ethernet Extensions
-
CXR offers a full range of access solutions and Ethernet extension on any type of media - copper, fiber optics and wireless, as well as through a network TDM PDH / SDH or linkage via modem serial interface X21 / V35.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
PoE Ethernet I/O Module w/ 3-axis Encoder/Counter Inputs
PET-7083
-
A great device, that works well for building automation, factory, and machine automation, remote maintenance, testing, and diagnosis, the PET-7083 is a 3-axis high speed encoder/counter module. Its each axis can be individually configured for Quadrant, Pulse/Direction or CW/CCW counting modes. The maximum input rate for Quadrant counting mode is 1 MHz, and for Pulse/Direction, CW/CCW counting modes is 4 MHz. The encoder/counter module is equipped a FRAM to retain the counter value after it is powered off. FRAM is a nonvolatile memory that can hold written data even after it is powered off. The data retention can be 10 years. And the feature can be configured as enabled or disabled.
-
Product
Ethernet Switch Module
VPX3-655
-
Curtiss-Wright Defense Solutions
The Curtiss-Wright VPX3-655 is a very versatile Ethernet switch supporting 1G, 10G and 40G ports, including 12x 10GBASE-T ports, providing high-speed connectivity for modular embedded computing applications.
-
Product
In-Line 1553 Ethernet Converter
NLINE-E1553
Ethernet Interface
Full BC, RT, and BM 1553 Controls Built-in a Small, Rugged, In-Line package. Control and convert 1553 messages to/from Ethernet in real-time (<20 uSec). Auto-bridge 1553 messages (BM) to UDP Ethernet without any programming.
-
Product
Ethernet Modules
-
The Ethernet Module supports a wide range of network protocols together with a standard RJ-45 Connector. Windows software is provided for testing and monitoring of the various I/O points. The Ethernet Module is compact and easily mounted in existing controllers or new designs for easy network connectivity.
-
Product
Gigabit Ethernet Tester Module for 1G and 10G Packet
GAO-ENET-103
-
GAOTek Gigabit Ethernet Tester Module for 1G and 10G Packet is designed for installation and maintenance of Metro/Carrier Ethernet and IP services. It supplies a compact test solution for 1G and 10G packet Ethernet, including ITU-T Y.1564 standard for SLA and OAM test features.
-
Product
3U CompactPCI Serial 9-slot SSL w/o RTM w/ Ethernet
1CPCIS-309-L200
-
3U CompactPCI Serial Backplane with 9 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 8x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh.
-
Product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
-
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Managed Ethernet Switch with L2/L3 Layer Support and Fiber Optic Option
ES2
-
Ethernet Switch module, ES2 provides up to 16 10/100/1000 Base-T 1 Gb ethernet ports. Additionally, there is one 10/100/1000 Base-T maintenance port interface, one RS-232 maintenance/console port interface, and a Fiber-Optic channel with four 10 Gb ports. It also provides numerous L2 and L3 networking, quality of service (QoS) and security features available as described below.
-
Product
ATCA Rugged Blade Processor With Dual Xeon Cascade Lake-SP, 100G Ethernet
ATC129
-
The ATC129 is a high performance ATCA processor blade featuring dual 24 core Intel® Xeon® processors, each with six banks of memory providing up to a total of 384 GB DDR4 memory with ECC.
-
Product
3U CompactPCI Serial 3-slot SSL w/o RTM w/ Ethernet
1CPCIS-303-L200
-
3U CompactPCI Serial Backplane with 3 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 2x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet routed as full mesh.
-
Product
3U CompactPCI Serial 5-slot SSL w/o RTM w/ Ethernet
1CPCIS-305-L200
-
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, without connectors for RTMs (Rear Transition Modules), Ethernet full mesh.
-
Product
100base-T1 Ethernet (BroadR-Reach®) Logging Expansion With Low Latency
PT-15B
-
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
