Jet Fuel
source of energy powering jet aircraft.
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
product
MFP-570 Main Fuel Pump
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
product
Fuel Tank Chamber
CSZ's fuel tank test chamber is designed to test the quality and reliability of automotive fuel tanks. Fuel tanks are temperature conditioned to -40C (-40F) along with a glycol mixture that is also chilled to -40C (-40F). The fuel tanks are filled with the glycol fluid and placed into the -40C (-40F) chamber. Tanks are soaked in the chamber for a predetermined length of time, removed from the chamber, raised to a specific height, and then dropped.
-
product
Fuel Injection Pressure Tester
33900
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
product
Air Jet Erosion Tester
AJ-1000
The state of the art Rtec Air jet erosion tester AJ-5000 allows to test repeated impact erosion test that delivers a stream gas with abrasive particles. The tester comes with close loop temperature control upto 900C. The tester is used to rank erosion of various materials, coatings etc. across a wide range of abrasive particle materials, shape, size at various temperature and impact speed.
-
product
POWERSTROKE FUEL INJECTOR TEST KIT
DFST20
*Tests Powerstroke engines from 1994 to current*Includes adapters necessary to pressure test the fuel system*Adapters can be used for testing at both the fuel filter and at the fuel pump
-
product
SpectrOil M/F-W Fuel Analyzer
SpectrOil M
The SpectrOil M/F-W is a compact, rugged and easy to use fuel analysis spectrometer. It is designed specifically for the analysis of ash-forming contaminants in fuel such as sodium, potassium and vanadium that cause corrosion or deposits at turbine operating temperatures. It measures trace quantities of dissolved or suspended contaminant particles in a fuel sample using the time-tested and reliable rotating disc electrode (RDE) technique.
-
product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
product
High Precision Fuel Flow Meter
This system measures fuel consumption of an engine operated in steady state with high accuracy.•0.02 to 90L/h and 4500:1 wide range measurement (H type)•Keep the temperature change of the circulation flow passage in the device within ±0.1℃ (variation per 1 minutes) to provide stable measurement.•Pipe arrangement which minimizes air bubbles that enter the system reduced the factor error causes.•Resolution has been improved by using an encoder with 1200P/R (Ten times of number of pulses to the existing model.)
-
product
Basic Fuel Injection Pressure Tester
FIT448
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
Basic Fuel Pressure Tester Kit
FIT450
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
product
Fuel Moisture and Fuel Temperature Sensors
Fuel moisture and fuel temperature sensors emulate and measure the moisture content and temperature of similarly sized twigs on the forest floor. The sensors are typically used as part of larger systems, such as fire weather stations with dataloggers and telemetry capability, to remotely assess changing fuel conditions and potential fire hazards.
-
product
Fuel Flow and Torque Converter
Model 44SM1
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
product
On-Board Fuel Consumption Detector
MF-3200
- High accuracy within ±0.2 % of reading- Compact size and light weight- A fuel cooling function is provided as standard.- Simultaneous measurement of temperature and pressure together with the flow rate
-
product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
product
High-Precision Fuel Flow Measurement System
It enables to keep the temperature fluctuation of the circulation flow path in the system within ±0.2 °C (for 1 minute), which achieves stable fuel flow rate measurement.
-
product
MASTER FUEL PRESSURE TEST SET
FPT5000
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
product
Fuel Density Meter
FD-5110
By connecting with the FM-3100 Digital Flow Meter, the FD-5110 Fuel Density Meter can measure temperature and density data in real time. In addition, the FP series Volumetric Flow Detectors with wide range ability and the FD-5110 are the best choice for achieving the accurate mass flow measurement.
-
product
IEC60529 IPX5/X6 Water Jet Nozzle
CX-IPX56
Shenzhen Chuangxin Instruments Co., Ltd.
The IPX5-6 Jet Nozzle consists of a jet handle that is equipped with a pressure gauge and an easy-to-adjust flow valve. The interchangeable nozzles assemble easily to the jet handle. The nozzles are made from stainless steel.
-
product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
product
Fuel Cell Test Systems
Fuel Cell Test System is a complete test station for operation and measurement of PEM/DMFC fuel cells.
-
product
Fuel Cell Test Stations
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
product
Fuel Injection Pressure Tester with 2 Gages
33950
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
product
IEC60529 Jet Nozzle IPX5/6
CX-IPX5
Shenzhen Chuangxin Instruments Co., Ltd.
Test Set consists of a jet handle that is equipped with a pressure gauge and an easy-to-adjust flow valve.The interchangeable nozzles assemble easily to the jet handle. The nozzles are made from stainless steel.
-
product
Fuel Cell Test Software
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
-
product
Fuel Flow Info
Custom range and dial markings are available. Call UMA representative for details!
-
product
Fuel Cell Test Station
E1PS is glad to bring you a low cost method to test fuel cells and produce professional test data results for under $1,000.00, fuel cell included! The Fuel Cell Test Station comes complete with everything but the hydrogen. There are three meters*, a load box, forced air housing and a fuel cell.
-
product
FUEL INJECTOR CANISTER CLEANER
FIT470B
*Cleans carbon from intake valves, fuel passages and cylinders with a professional carbon cleaning solution*Will restore the original spray pattern more effectively, giving improved performance, fuel economy and emission tests*Uses shop air with any professional canister cleaning solution on the market
-
product
Fuel Hose Assembly Tester - USAF
9201
The purpose of this equipment is to provide a source of high pressure fluid for proof testing of fuel hoses after assembly or on a periodic schedule as required by specification.
