-
product
FieldFox Handheld Microwave Spectrum Analyzer, 44 GHz
N9961A
5 kHz to 44 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 7.1 lb. (3.2 kg)
-
product
IC Side Channel Analysis
These probes allow you to couple fast, transient magnetic field, E-field, and current pulses into ICs.
-
product
High Voltage Surge Testers
HVST
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
product
Lightning Surge Generator
SKS-0510I
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
product
LED Phosphorescence Light Sources
SpectraLED
Innovative and affordable pulsed light source for phosphorescence measurements from deep UV to NIRThe SpectraLED is a novel light source designed specifically for the measurement of phosphorescence lifetimes. These phosphorescence sources are based on LED technology and the emission wavelengths range from the deep UV to the NIR.
-
product
Solid State Broadband High Power Amplifier
Model 2215
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
product
Characterization Platform
This standalone integral software and hardware platform is capable of functioning as an independent single-channel or virtual multi-channel characterization test subsystem. The platform is USB controlled to provide temperature, RF-signal and bias-control to a device-under-test (DUT) for semiconductor performance measurement. When used in conjunction with Accel-RF's embedded Pulser-Card Assembly, the test device is capable of pulsed DC and RF stimulus.
-
product
Incremental Encoders
Versatile, compact and flexible – Incremental encodersIncremental encoders are used when retention of absolute position upon power loss is not required. These encoders provide information about the position, angle and number of revolutions. The number of lines per revolution determines the resolution. The current position can be determined by counting these pulses from a reference point. Upon activating the machine, a reference run to the reference point is required to determine the absolute position of the encoder.
-
product
Advanced Digital Lab Trainer
Designed to do experimentation with Digital & Analog circuits in the laboratory. It is a self contained trainer including Fixed & Variable DC Power Supplies, Pulse Generator with TTL/CMOS, Pulsar switches, etc In a single unit. It is very useful in project work and testing. A number of ready to use experiment circuits boards are available(Optional).
-
product
12-Watt Pulsed FAYb Fiber Laser
LP-V Series
Panasonic Industrial Devices Sales Company of America
The LP-V series is a 12-watt, pulsed fiber laser.Characteristics:- Very high resolution- Fine marking area- Small air cooled head
-
product
Accelerometer & Platform Test Bench
mS 1115
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
product
Multi-Battery Tester
MBT-1
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Fast Transient Burst Simulators
FNS Series
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
product
AC/DC Power Capacitors
ACF Series
For 70Vac~400Vac / 100Vdc~700Vdc Pulse Current requirement, please refer to our DC Pulse Current Capacitors for Power Electronic applications.For continuous and High RMS Current requirement, please refer to our High AC Current Capacitors LC series, which support continuous duty even at +105C.We manufacture AC Filter Capacitors for a wide variety of applications with different Capacitances, Voltages, Discharge Energy ranges, dv/dt, Pulse Discharge Currents, RMS Currents, frequency ranges, size restriction and even capacitor mountings.
-
product
Capacitor Charging Power Supplies
Excelitas Capacitor Chargers are tailored to meet your exact needs by configuring modular platforms based on proven designs. Single-phase AC input designs are capable of up to 6 kW of output power and our three-phase designs provide up to 35 kW of output power. A modular design approach results in lower cost, higher reliability, and faster time-to-market. Typical applications for capacitor charging power supplies include flashlamp pumped laser systems (Nd: YAG, pulsed lasers, dye lasers, Intense Pulsed Light Systems (IPL) and aesthetic Medical Laser Systems, Medical Holmium YAG Laser), excimer lasers, pulsed UV curing and sterilization, radar and RF systems.
-
product
Non-contact Conductivity Type (P/N) Checker For Quick Check
PN-50α
*Principle: Photovoltaic effect by light pulse irradiation*No damage and no stain by Non-contact method*Possible to check even oxidized film on wafer surface*Instantly discrimination by optical pulse illuminate
-
product
Source Measure Units (SMUs)
B1511B
The SMUs of B1500A integrate 4-quadrant voltage/current source and measurement capabilities for accurate IV measurement with the range of 0.1 fA - 1 A / 0.5 µV - 200 V. It supports spot, sweep, pulse sampling and QS-CV measurements.
-
product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Dry Dielectric RF Coaxial Loads
4000 Series
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
High-Performance Autoranging DC Power Module, 60V, 17A, 500W
N6756A
The Keysight N6756A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
product
Clock Synchronization
Analog Devices Clock synchronizers are designed for wired networking applications, providing the clock redundancy functionality needed to maximize system uptime. Our technology supports clock synchronization with common standards, including 1 pulse per second (PPS) output signal from a GPS receiver. GPS signals are broadly available and utilize an extremely stable atomic clock as its time base, but they are often noisy. Systems rely on the IEEE1588 timing protocol to establish synchronous communications across the wired network, including synchronous Ethernet and synchronous digital hierarchy (SDH) to optical transport network (OTN) mapping/demapping. The IEEE1588 protocol has emerged as the preferred method for Clock synchronizing systems throughout both computer networks and local area networks (LAN).
-
product
Pulsing and Pulse Waveform Control
Paramount Plus
Get the broadest feature set available in a pulsed-RF product. The Paramount Plus offers precise RF regulation, sophisticated pulse manipulation, and advanced data acquisition. Designed to cover an extensive range of RF energy — frequencies of 1 to 60 MHz and power levels of 1.5 to 15 kW — the Paramount Plus delivers the repeatability and reliability you require.
-
product
Pulsed Laser and LED Light Sources
NanoLED
The NanoLED range is a novel and economical light source system that utilizes pulsed laser diode and LED technology to generate short optical pulses over a wide range of repetition rates and wavelengths. Optical pulses as short as 70ps can be generated at repetition rates up to 1MHz.
-
product
Digital ESU Analyzer
ESU-2050P
Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer. The Pulsed Model is compatible with all continuous output generators (same as standard model), plus generators with pulsed output waveforms.
-
product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
product
Combination Wave Generator
Shanghai Guantu Technology Co., Ltd.
GCW series combined wave generators can generate high energy surges for combined wave testing. It has the characteristics of fast rise and long pulse duration. According to different modulation components, different surge waveforms can be generated; the control system can automatically record and analyze the above surge waveforms. standard:IEC60060-4-5, IEC61643-11, UL1449-2006, GB18802.1, GB/T18802.21,
-
product
Device Parameter Analysis
bsw TestSystems & Consulting AG
The complexity of DC Parametric Characterisations has significantly increased with the level of miniaturisation in the semiconductor industry. The demand is not only on the precision of the measurements. New measurement methods have emerged to gain insight into phenomena previously unknown or only of marginal relevance. One example is "Pulsed IV" which is now widely in use. The modular concept of the Keysight B1500A allows users to tailor their instrument exactly to their needs. Flexible upgrades ensure the investment for many years. Together with bsw AG you will get an optimum solution for your application. Our experts provide not only support for the instrument itself but have also working knowledge of all the solutions surrounding it. This includes Cabeling and Adapters, Fixturing for packaged Parts and of course Wafer Probing. We help customers from replacements of broken or worn-out parts to planning and deployment of turn-key-systems.
-
-
product
Mode Locked Synthesizer
IT9200
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
product
Pulse Function Arbitrary Noise Generator
81160A
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
