-
Product
12-Bit, 2.5 GSPS Digitizer Optimized for Pulse Detection
ADQ32-PDRX
-
ADQ32-PDRX acquires the input signal via a single connector and uses an onboard splitter to separate the signal into two paths with different gain settings. The high gain path is used to accurately capture low-amplitude portions of the input signal whereas the low gain path ensures the acquisition of high-amplitude peaks without causing saturation. The two signal paths are then combined in real-time inside the onboard field-programmable gate array (FPGA) to create a digitized output with improved performance.PDRX increases the dynamic range by 3 bits and is fully integrated into the digitizer for fast and easy system-level integration. ADQ32-PDRX is therefore comparable with a 16-bit digitizer in terms of dynamic range, but with the benefit of offering a higher sampling rate.
-
Product
Pulsed High Field Magnetometer
TPM
-
This is the equipment evaluating the magnetic properties of rare-earth such as Js, Jr, Hcb, Hcj, (BH)max, HK and SR etc.
-
Product
Micromachining Laser Systems
-
Versatility in terms of materials Taper controlled drilling Only top – quality components Intelligent laser machining software Beam focus adjustment Beam power (pulse energy) control Many options for system customization Table top system Small footprint Cost effective workstation User-friendly, flexible, upgradeable system control
-
Product
150A, 12 MHz CURRENT PROBE, BNC, AC/DC, 150A rms, 300A Peak Pulse
T3CP150-12
-
150A, 12 MHz CURRENT PROBE, BNC, AC/DC, 150A rms, 300A Peak Pulse.
-
Product
Standard RF Fixture
-
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
Product
RF Signal Generators
-
As Rigol's RF first signal source, the DSG3000 series offers standard AM/FM/ØM analog modulation, as well as options for I/Q modulation and I/Q baseband output. The instrument is available with maximum frequencies of either 3 GHz or 6 GHz. Featuring a high signal purity with phase noise measuring <-110dBc/Hz@20kHz (typical) and a wide output range of -130dBm to +13dBm, the DSG3000 RF signal generator has standard pulse modulation with an on/off ratio of up to 80dB, with optional pulse train generator available. The DSG3000 series also has an amplitude accuracy of <0.5dB (typical).
-
Product
Single Channel Peak Power Meter
8501A
-
The Spanawave/Giga-tronics 8501A Single Channel Peak Power Meter combine CW power measurement with the ability to make precise peak power measurements at any point on a pulsed waveform. This dual, built-in capability lets you make CW measurements and analyze pulsed waveforms with a single instrument.
-
Product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX52
-
The N5295AX52 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Laser Applications
-
Quantum Composers offers a diverse family of lasers, laser systems, and modules, including DPSS, Nd: YAG, and pulsed lasers. Our MiniJewel and MicroJewel lasers are now available in 2 different energy options to allow customers to tailor the laser to their specific applications.
-
Product
SFG Spectrometer
-
Ideal laser spectroscopy tool for in-situ investigation of surfaces and interfaces. SFG spectrometer operates from 4300 to 625 cm-1 and provides < 6 cm-1 spectral resolution. The heart of the system is a picosecond Nd:YAG laser generating 25 ps pulses that pump an OPG/DFG delivering from 260 to 20 µJ per pulse across the IR range
-
Product
Flow Sensors
-
SICK provides innovative sensor solutions for flow measurement technology which combine flexible measuring methods and rugged equipment design with cost-efficient connection concepts to integrate higher-level systems. Whether you need to detect the current flow rate value using analog values or find the quantity using pulse detection – SICKs flow sensors are always reliable and safe and can work with a wide range of media under difficult process and ambient conditions.
-
Product
FPGA Workbench and I/O Cards
-
FPGA Workbench software provides a complete development environment for building customized solutions based on Concurrent’s programmable FPGA cards. FPGA Workbench includes a powerful GUI for selecting and configuring a wide range of pre-developed data acquisition and industry-specific modules to meet your application requirements. The library of functional IP modules includes pulse width modulation, analog I/O, digital I/O, SENT protocol, encoder, ignition, injection, crank/cam shaft, wheel speed sensor and change-of-state.
-
Product
Paddlewheel Flow Sensor
2537
-
The Signet 2537 Flow Sensor is the next generation in fluid measurement technology from the inventor of the original paddlewheel flowmeter. This sensor is an enhancement on what is already an industry standard. It has the added functionality of various output options including flow switch, pulse divider, digital (S3L) or 4 to 20 mA. Additionally, it offers low flow, low power and high resolution and can be configured on-site directly through the built-in user interface.
-
Product
Wall-Mounted Electronic Energy Meter
MWH-7W
-
The MWH-7W series is an electronic energy meter with excellent performance, the main function is high-precision energy metering, the panel has LCD display, the energy value is clear and easy to read. The power meter provides functions such as pulse output and RS485 communication interface, which is convenient for the user to check or structure into a centralized meter reading system.Panel and wiring cover with lead seal, in accordance with CNS 14607 specification design.
-
Product
Basic Pulsed-RF Measurements
S96025B
-
Enables internal pulse generators to control the internal pulse modulators and provides an integrated pulse application that uses the wideband-detection method. Requires hardware Option 021 pulse modulator hardware.
-
Product
4-Axis EtherCAT Motion SubDevice
AMAX-3245
-
Max. 5 MHz, 4-axis pulse outputEncoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modeBoardID is switchableEasily visible LED indicators on board to do diagnosisDirect wire to servo drive to save terminal board space while installationHorizontal installation for for servo or stepping motor driverSuitable for DIN-rail mountingProgrammable interruptMemory buffer (10K points) for trajectory planning which is designed in DSP4-axis position compare triggering up to 100 KHz, and memory buffer is up to 100 K pointsPosition latchSupports gantry mode by semi-closed loop pulse train controlLTC-dedicated input channels & SVON/CMP/RST/ERC-dedicated Output channels are switchable for general input and output purposes
-
Product
Charged Plate Monitor
Model 280A
-
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
Product
Picosecond Timing System
-
Specialized, high-precision electronic system designed to generate, distribute, and measure timing pulses with a resolution.
-
Product
Signal Generators
-
2, 4 and 8 Channel Arbitrary Waveform Generator and Pulse Pattern Generator solutions are ideal choice in automated test benches, for physics experiments, semiconductor tests, analog and digital debugging.
-
Product
Peak Power Analyzer
4500C
-
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
Product
Laser Power / Energy Meter
StarBright 7Z01580
-
*Compatible with all standard Ophir thermal, BeamTrack, pyroelectric (PE-C series) and photodiode sensors*Brilliant color large size TFT 320x240 display*Choose between Digital with Bargraph, Analog Needle, Line Plot (for laser tuning), Pulse Chart, Pass/Fail, *Position, Stability, Real Time Statistics displays*Sophisticated power and energy logging, including logging every point at up to 5000Hz with Pyro sensors*Math functions for advanced processing such as Density, Scale Factor, Normalize against base line, etc.*Can mix functions together and display the results graphically. Function results can also be logged.*USB Disk on Key (Thumb Drive) for nearly unlimited data storage.*USB and RS232 interfaces with StarLab PC applications and User Commands document
-
Product
4-Axis Pulse Motion Controller
AMP-104C
-
The AMP-104C is a cost-effective 4-axis motion controller card with a PCI Express® interface that can generate a pulse train up to 4.9MHz to control a motor. With more general purpose IOs and 4-channel encoder feedback input, the AMP-104C can be used for a multitude of scenarios or applications. As a motion controller, the AMP-104C provides non-symmetric acceleration and deceleration speed profile settings, T-curve and S-curve speed profile control, and selection of motion stop method.
-
Product
Lightning Surge Generator
SKS-0510I
-
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
Function/Arbitrary Waveform Generators
SDG1000X Series
-
SIGLENT’s SDG1000X is a series of dual-channel function/arbitrary waveform generators with specifications that include up to 60 MHz maximum bandwidth, 150 MSa/s sampling rate and 14-bit vertical resolution. The proprietary EasyPulse & TrueArb technique helps to solve the weaknesses inherent in traditional DDS generators when generating pulse waveforms, and the special square generator is capable of generating square waveforms up to 60 MHz in frequency with low jitter. With these advantages, the SDG1000X can provide users with a variety of high fidelity / low jitter signals while meeting the growing requirements of a wide range of complex and varied applications.
-
Product
50MS/s Dual-Channel Arbitrary Waveform Generator
WW5062
-
Model WW5062 represents the next generation of products in the field of function, pulse and arbitrary waveform generators. This instrument is superior and far more versatile than any existing equivalent whether it is an analog or digital product. As a waveform source, this model can replace analog generators in almost every application.
-
Product
Optical SpO2 Pulse Oximeter Simulator
OX-1 OxSim®
-
Test the complete SpO2 system, including the sensor, extension cable with the OxSim® Optical SpO2 Pulse Oximeter Simulator. Slips into your shirt pocket and operates easily with just two buttons on a single AA battery. The auto-detection of the Sensor type eliminates the need to select the manufacturer oximeter under test. The optional serial communications port enables users to expand simulation settings for Saturation, Pulse Rate, and Perfusion Index, ideal for applications where a wide range of simulations is needed.
-
Product
LST-2000 Laser Safety Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
The system can measure the spectral power distribution, radiant power, radiant energy, apparent light source size, pulse energy and other parameters of the laser light source, and classify the laser light source according to the standard IEC 60825.1. Because laser measurement involves more condition parameters, limit calculation and judgment process is complex, so this system adopts systematic design, the measurement complexity is simplified, the hardware adopts componentization module, users only need to follow the software prompts, carry out the corresponding steps of operation can accurately measure the effective radiation value under the corresponding conditions. The software calculates the relevant reachable emission limits and automatically classifies the laser product's safety level.
