-
Product
Dual Digital Aquisition System For Charge Integration And Pulse Shape Discrimination
DT5790
-
The DT5790 operates upon the DPP-PSD firmware, specially developed for Charge Integration and Pulse Shape Discrimination. DPP-PSD is based on an advanced on line Digital Dual Gate Charge Integration allowing an effective data analysis even at high count rate. It performs input signal baseline calculation, self-triggering and double-gate charge integration with programmable parameters, double integration of both prompt and total charge for Pulse Shape Discrimination and pedestal subtraction for energy calculation.
-
Product
Femtosecond Autocorrelators - Pulse Measurement Systems
Reef
-
The autocorrelation technique is the most common method used to determine laser pulse width characteristics on a femtosecond time scale . Del Mar Photonics autocorrelators have been specifically designed to measure the width of pulses from femtosecond lasers.
-
Product
Pulse & Delay Generators
-
Berkeley Nucleonics Corporation
Provides high frequency pulses, delays and bursts. It is an ideal testing and timing control instrument for electronics, lasers or camera setup.
-
Product
Launch Box & Pulse Suppressor
OTDR Sidekick
-
Intended to eliminate the "dead zone" at the beginning of a fiber cable when using an OTDR, The Sidekick from M2 Optics is a compact, durable solution for both field and laboratory use. Commonly referred to as a launch box, pulse suppressor, or launch cable, this durable test box is also used as a fiber optic delay line and for a variety of other short-distance testing and training applications.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
10MHz Pulse Generator With Delay
TGP110
-
0.1Hz to 10MHz frequency rangeIndependent control of pulse frequency, width and delay50ns minimum pulse widthSquare wave, double pulse & delayed pulse modesFree-run, gated and triggered modes50 Ohm output: 0.1V to 10V amplitudeTTL/CMOS and Sync outputs
-
Product
Group Pulse Generator
STT-EFT-5K series
-
Beijing KeHuan Century EMC Technology Co,.LTD
STT-EFT-5K series group pulse generator is designed to determine a common and reproducible basis for evaluating the performance of electrical and electronic product power lines, signal lines or control lines when subjected to electrical fast transient pulse group interference. The performance of the generator meets the requirements of IEC 61000-4-4 and GB/T 17626.4 standards. Application areas: industrial control, home appliances, medical electronics, communication electronics, components, automation control, etc...
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
System Tests Radar Pulse Stability
PN9002
-
Noise eXtended Technologies S.A.S.
The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.
-
Product
Split type Pulse Current Sensor
CTF-05T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For detecting current pulse with open collector output (for power pulse)
-
Product
30A, 50 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-50
-
30A, 50 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
Pulse Tools
-
Faster than hand tools, more powerful than air screwdrivers, and safer than impact drivers, Mountz pneumatic pulse tools are a top solution for heavy fastening operations. Their pulse drive protects workers from injuries caused by high torque shut-off reactions. That means they can safely be used at higher torque settings than other power tools. High-speed rundowns decrease production cycle times, and the durable construction and simple maintenance needs ensure consistent tool uptime. Plus, a precise hydraulic shut-off keeps fastening work accurate for even the most heavy-duty applications.
-
Product
Pulse Rate to 4-20mA or Voltage Converter
SY020
-
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
50 µs Pulse Medium Current Source/Measure Unit (MCSMU)
B1514A
Source Measure Unit
The 50 s Pulse Medium Current SMU is an SMU designed for faster pulsed IV measurement. It enables a pulsed measurement down to 50 s pulse width, a 10 times or more narrow pulsed measurement than provided by a comparable conventional SMU. In addition, the instrument offers a wider range and versatility, up to 30 V / 1A, with voltage/current programmability. It is useful to characterize high to medium power devices on the new materials such as SiC and GaN, and organic devices, and the MCSMU expands your choices of pulsed IV measurement.
-
Product
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse
T3CP50-50
-
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse.
-
Product
Isolation Pulse Transmitter
PA-330Z
-
The PA-330Z receives the square wave signals from the rotary encoder, and converts it to low impedance signals suitable for long distance transmission after wave-shaping and amplifying via photo couplers which provide isolation between input and output.A 12VDC external power supply is provided for use with the DC powered RP series encoder.The case is sealed construction which allows closely mounting to the encoder.
-
Product
Pulse Tesla Meter
GP-300
-
Pulse field intensity can be read directly. Wave form is observed by oscilloscope. Measuring range:0.01T~9.99T .
-
Product
Pulse Function Arbitrary Noise Generator
81160A
Arbitrary Waveform Generator
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
Product
Pulse Current Generator Multi-Pulse Generator
-
Shanghai Guantu Technology Co., Ltd.
What is the difference between ordinary current and pulse current?The difference between ordinary current and pulse current: ordinary current is continuous and uninterrupted current.Pulse current is a current whose direction does not change and whose intensity changes periodically with time.
-
Product
30 A, 10 MHz Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 3 Meter Cable
CP030-3M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
High Performance Function/Arbitrary/Pulse Generator 25MHz Or 50MHz, 1 Or 2 Channels
TG251xA/501xA Series
-
One or two channels0.001mHz to 50MHz/25MHz range; 14 digits or 1uHz resolution.Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic and PRBS.True pulse generator with variable delay and variable rise/fall.Arbitrary waveforms of up to 128K points at up to 125MS/s.Waveform storage using USB flash drives.Large graphic LCD with simultaneous text and waveform display.Comprehensive internal and external digital modulations including AM, FM, PM, PWM, FSK, BSPK, Sum and PRBS.20mV to 20V pk-pk output from 50Ohms ; plus multi function aux. out.Storage for multiple instrument set-ups in non-volatile memory.Waveform Manager Plus for Windows software included.Programmable via USB and LAN (LXI) interfaces; GPIB optional
-
Product
Turn Key Laser and LED Sources with Picosecond Pulse and Repetition Rate up to 100 MHz
DeltaDiode
-
DeltaDiodes utilize laser diode and LED technology to generate short optical pulses over a very wide range of repetition rates and wavelengths. Optical pulses as short as 50ps can be generated at repetition rates up to 100MHz.
-
Product
OEM Pulse Energy and Power Measuring Instrument
LEM 2510
-
This OEM-Meter is assembled in a standard cassette for the industrial 19? system. It has a width of 21TE. A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity, allow to use a wide range of sensor heads.?
-
Product
IMPATT Noise Generator CW & Pulse At W-band, 94 GHz :
-
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
-
Product
Multifunction Counter (Pulse Input)
CM1-CT
-
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
Product
Group Pulse Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Group Pulse Generator.
-
Product
High Voltage Pulse
-
For thicker coatings it has fully adjustable output voltage from 5 kilovolt to 25 kilovolts. For very demanding conditions, a sensitivity switch offers additional control.
-
Product
Split type Pulse Current Sensor
PCT-06
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
Product
Pulse Generators
-
An electronic circuit or a piece of electronic test equipment used to generate rectangular pulses.
