-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Signal Generator
-
bsw TestSystems & Consulting AG
Especially for signal generation above 50GHz and in waveguide bands is done with a standard lower microwave generator and then the signal is frequency multiplied to get to higher frequencies. The frequency multiplied signal may optionally be filtered to make it spectrally pure and/or amplified to come to an appreciable signal level.
-
Product
Small Device Noise Emission Test System
-
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Product
Direction Finder Components
-
Doppler Systems offers direction finder components that can be paired with your narrow band FM receivers to create an accurate, low-cost radio direction finder (RDF). Our direction finder components include processors and fixed site and mobile antennas.
-
Product
Internal Antennas
-
Pulse offers a large selection of internal antennas that are designed into an incredibly diverse selection of solutions, from smart home IoT devices to utility meters, from point of sale products to wireless charging. The PCB antennas, including those made with flexible material, are made to be mounted or adhered against a plastic surface and connect via cable to your PCB, and cover the ISM, WiFi, GNSS, and cellular bands. The NFC selection for 13.56 MHz will work with both 50 and 80 Ohm radios and include antennas with a ferrite backing to work even when mounted against metal. The selection of active GNSS patch antennas with cable are perfect for ensuring your device’s whereabouts are accurately tracked. Finally, the many transmit and receive coils for wireless power charging will add this popular consumer capability to your product, cutting one final cable from design. Use the product finder below to find the perfect internal antenna solution for you.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Sound Power Reference Source
Qref
-
Precision omni-directionallity in all directions, horizontal and verticalplane. This source has a frequency range of application between 100 and8000 Hz (third octave bands) Despite only weighing 1.4 kg and having a diameter of 105 mm, it produces a maximum sound power level of Lw 104 dB.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
-
Product
Microwave and mmWave
Tx/Rx
-
Analog Devices offers complete transmitter (Tx) and receiver (Rx) solutions for microwave (w) and millimeter wave (mm wave) applications. With the need for greater integration and improved performance in multiple industries and technologies, Analog Devices' industry-leading, ready to use transmitter and receiver chipsets for E band, V band, and microwave applications help designers reach new limits in their radio designs. This product family's integrated chipsets can be used for backhaul communications, VSAT, small cell networks, broadband local networks, and other applications.
-
Product
Power Amplifier (DC Powered)
-
RF Lambda’s DC solid state power amplifiers (PA) are used in a variety of applications and offer high output power, wide band operation and good linearity. Hermetically sealed options are available upon request.
-
Product
Analog Control Variable Gain Amplifiers (VGAs)
-
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
Product
Mixer
-
RF Lambda’s wide band mixers are used for frequency conversion. Both active and passive versions are available with high IP3 and low conversion loss. Hermetically sealed options are available upon request.
-
Product
Digital AC milli Volt meter
-
PGP Electronics Private Limited
PGP Electronics Digital AC Mill voltmeter is a very versatile and general purpose equipment for the measurement of audio frequencies. It is useful in measuring low amplitude signals over a wide band of frequencies with precision. Its has a wide band width and sensitivity is 10uV. This instrument is useful for all amplifiers/ audio system manufacturers, college laboratories to measure input/output of any amplifier as well as frequency response of that amplifiers. .
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
Amplifiers
-
Fully automatic, legal limit plus headroom amplifierAlpha’s low-drive, tube amplifier design delivers the cleanest possible signalOperates on all Amateur Radio Bands 160M thru 10MSingle, easy to find, inexpensive 3CX1500A7 8877 type tubeInternal, automatic 4 port antenna switch capable of combining any 2 antenna portsAlpha’s Legendary service and support4 year limited warranty on hardware, 1 year on tube1500W, 100% duty cycle, no time limitation, key down foreverRugged construction built to last
-
Product
2 in 1 Power Meter
FiberPal OT-2000-V
-
The FTTx Wide Band VFL Meter, OT-2000-V, is a powerful optical measuring tool which can be used in various optical fiber systems and applications, especially in FTTx field installation and maintenance. With 850, 1310, 1490, 1550 nm calibration wavelength, it is ideal for both single mode and multimode fiber field installation and maintenance. The additional 650nm light source makes for a convenient, easy to use yet powerful device to check for broken fibers as well.
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
Electrodynamic 2-Axis Switching, Simultaneous Vibration Tester
-
It is an electrodynamic 2-axis switching, 2-axis simultaneous vibration tester with a test frequency band up to 2000 Hz.
-
Product
Remote Radio Head 50 GHz
CMPHEAD50
-
The R&S®CMPHEAD50 is the only remote radio head supporting bi-directional testing at five mmWave frequency bands with one hardware set and EVM booster ports. It extends the R&S®CMP200 radio communication tester to frequency range 2 (FR2/ FR2-1). The improved performance ensures optimum accuracy for testing next generation FR2 RF designs – from early development to final certification and regulatory compliance. Test with confidence and ensured RF performance with the latest state-of-the-art measurement solution from Rohde&Schwarz.
-
Product
RF Shielded Box
LTL B5001
-
LTL B5001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B5001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
200KHz / 10000Freq.Point LCR Meter
MCH-2816A
-
It has high test frequency of 300kHz and 0.01Hz stepping arbitrary programming, and it has 10mV-2V signal level, all making it meet the precision test requirements of production line quality control, in-coming inspection and lab. Its HANDLER, RS232c interfaces are used for the component automatic sorting system, which provides the conditions for computer telecommunication and test recording. Flexible frequency-response analysis:Due to non-ideal inductor, capacitor and resistor, in order to precisely evaluate the characteristics of one component in one frequency band, MCH2816 could use its signal generation ability with 10mHz resolution to correctly analyze frequency response of the component parameters in any frequency band. In particular, it can do the precise measuring of the resonant impedance of the low-frequency ceramic resonant devices which has wide impedance range.
-
Product
Measurement
Vibration Meter
-
The input signal of the Vibration meter software, which is the output signal of the accelerometer, i.e. the vibrational acceleration signal, is filtered by means of one of four possible digital band filters. Then, based on this signal, vibrational velocity and displacement signals are calculated by means of integrating filters. Thus, the software generates three signals which are transferred to the ZETLAB data server virtual channels created by the program and having the word “Acceleration”, “Speed” or “Displacement” in their names, respectively.Signals are averaged for a selected time interval (0.1 s, 1 s, or 10 s), after which the obtained values are displayed in the dialog box elements of the Vibration meter program. It is possible to display a root-mean-square (RMS), average amplitude or peak value.
-
Product
High Performance LWIR SLS Camera
FLIR X6900sc SLS
-
The FLIR X6900sc SLS is an extraordinarily fast, highly sensitive LWIR camera designed for scientists, researchers, and engineers. The strained layer superlattice (SLS) detector offers shorter snapshot speeds, wider temperature bands, and better uniformity than current LWIR or MWIR alternatives. With advanced triggering, on-camera RAM/SSD recording, and a four-position motorized filter wheel, this camera offers the functionality to stop motion on high-speed events both in the lab and at the test range.
-
Product
IQ Networks
-
Teledyne Microwave Solutions (TMS) offer a capable range of high performance IQ Modulators and Image Reject Mixers as well as IQ (Quadraphase) Modulators which can be used on applications from commercial test equipment to space qualified projects. IQM products can be used either as an IQ modulator or IQ demodulator and cover several frequency bands from 1.4 GHz to 18 GHz.
-
Product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400B (2RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
Product
2-In-1 Wi-Fi Tri-Band MIMO Antenna, Covering 2.4/5/6GHz Bands, Support Wi-Fi 6E/7, IP67
AIW-514
-
2-in-1 WiFi Tri-band MIMO antennaDipole antenna with omni-directional radiation patternCovering 2.4GHz/5GHz/6GHz bandsSupport latest Wi-Fi6E/7Screw MountRP-SMA male connectorIP67 waterproof resistant for outdoor
-
Product
Silicon Detectors
-
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
Product
IP67 DC Blocking Splitter Combiner
PD5123
-
INSTOCK Wireless Components, Inc
PD5123 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5123 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
