Tension
forces causing extension.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Gravity, Electrical, Magnetic, Tensiometers, Tensile, Extensometers
-
Product
Single Fiber Strength Tester
TB400C
-
TESTEX Testing Equipment Systems Ltd.
Single Fiber Strength Tester, suitable to test the tension strength and elongation of chemical fiber, cotton, wool, ramie, silk, glass fiber, fine metallic thread, etc.
-
Product
Running Line Tensiometer
TIMH
-
The TIMH - running line tension meter range are built with dockside, marine, offshore, towage and salvage applications in mind. It is particularly useful where there is no anchor or dead end on the line to rig a Straightpoint Radiolink or Loadlink digital dynamometer to measure tension force.
-
Product
Load Cells
-
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
S-Type Load Cells
-
S-Type Load Cells take their name from their shape – as you can see from the images below – they are in the shape of the letter “S”. These load cells are commonly used in tension applications; mechanical-to-electrical scale conversions as well as weighing applications including cranes etc.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Stationman Speaker Probe
250 SSP
-
This probe is designed for those technicians that want the best tool available. The Model 250SSP is supplied with a cone-shaped tip and a duckbill tip that is longer and flatter, permitting insertion into larger cables, or cables under tension where slack cannot be obtained. Another feature is the built in speaker for audio without the need for a butt set or headset. The speaker is operated by a slide switch that has a "lock" position for continuous monitoring.
-
Product
Manual Test Stands
-
Manual test stands offer basic force testing and economy.Lever models enable rapid testing of compression or tension, up to 220 lbf.Wheel-operated test stands enable precise control for either compression or tension and the force gauge remains in position when the wheel is released. Wheel stands are offered in a wide range of capacities from the 11 lbf capacity micro-movement stand up to 750 lbf models.
-
Product
Optical Tensiometers
Theta High Pressure
-
The Attension® Theta High Pressure is a tensiometer for measuring wettability and interfacial tension at high pressures and high temperatures within enhanced oil recovery research. With the harsh conditions of an oil reservoir in mind, the instrument is designed to ensure ease of use and yet offer wide measurement possibilities.
-
Product
Display-Only Dynamometer Testing Instrument
DynTek-PC
-
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
-
Product
Dynamometer
-
The PIAB Dynamometer is excellent for measurement and control of tension forces and weight, where accuracy, reliability and safety in all conditions is required. The PIAB Dynamometer conforms to the International Standards for Safety Inspectorates. The PIAB Dynamometer is an all-weather instrument, equally suitable for use in the laboratory as in the field for weighing and measuring mechanical tension forces.
-
Product
High Altitude Wiring Clamp
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Product
Ultra Precision Mini Load Cell Universal/ Tension or Compression
MDB SERIES
-
The MDB Series Load Cells was designed to help fill the growing need for a greater selection of high accuracy load cells for use in space limited applications. The anodized aluminum MDB's are compliant in tension and compression, therefore, a good choice for in line through zero applications, as well as single direction tension or compression. Applications may include load feedback for process control, low capacity tensile testing machines, robotics, or designed into your product. Give us a call, we would be pleased to discuss your application requirements.
-
Product
High Voltage Power Capacitors
-
Lifasa - International Capacitors, SA
Capacitors of correction power of cos φ and filtering of harmonics for AT of Lifasa, are manufactured under the base of the container / stainless steel box and porcelain terminals. There are two types, depending on the connection mode that we are going to use:*Single-phase (1 or 2 terminals) with internal fuses, for connection to the network through a double star. Recommended for networks of tension superior to 11 Kv or need of equipment of high power.*Three-phase (3 terminals) with internal fuses, for direct connection to three-phase network. Recommended for voltage networks lower than 11 Kv.
-
Product
Digital Torque Meter Torsion Tester
HN-1E~20E
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital Torque Meter is an intelligent metrologic instrument, which is designed for various torque test and calibration. It's mainly used for electic/manual torque drive, torque screwdrivers, bolt driver, tension wrench and other testers and products which refer to tightening force. It is widely applied in these industries, such as electrical manufacturing, machine manufacturing, car light industry, professional research and tests, and so on.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Compact Tension Grips
-
These compact tension grips are for plane-strain fracture toughness tests of metallic materials. Fracture toughness testing involves applying static loads to a notched sample to investigate brittle crack propagation and fracture conditions.
-
Product
Cable Pulling Analysis
CABLE
-
CABLE quickly solves complex three-dimensional cable pulling tension and sidewall pressure calculations, allowing you to make rapid and accurate design decisions.Don't leave installation to chance.
-
Product
Zipper Reciprocation Tester
UI-FT34
-
Zipper Reciprocation Tester is used to test zipper fatigue resistance under lateral and longitudinal tension.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Timegrapher App
Timegrapher X
-
The speed of a mechanical wrist watch is not constant. It fluctuates with build quality, watch position, mainspring tension and even temperature. The Timegrapher X iOS app is a unique tool that helps you find, observe and understand patterns developing over time.
-
Product
Spring
-
Our Springtest range of spring testers are designed to check and measure the force of all types of spring: compression, tension, etc., simply and accurately.
-
Product
General Purpose Quartz Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
General Purpose Low Profile
-
Our low profile load cells feature an advanced structural design that makes them extremely durable, accurate, and resistant to large extraneous shear and moment loads. To perform in a linear and predictable manner, the outside diameter of the load cell must be bolted to a flat rigid surface. When this is unavailable, our factory installed base provides a convenient threaded attachment point for easy installation and use in both tension and compression. All low profile load cells are stocked with the mounting base installed, but we can remove the base upon request.
-
Product
RFID Label Inspection System
Eurotech RFID FS
-
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
Product
Zipper Tester
-
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
Product
Threaded Load Button
2000 Series
-
This model is a threaded load button for tension and compression load measurements up to 5000kg/ 10000lb. Fully welded cover (for SS load buttons), amplified and digitised versions are available on request. We can also customise this sensor for other thread sizes and cable sizes
-
Product
Servo-Pneumatic Asphalt Testing System
-
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
