-
product
Standard Voltage 37-Pin D-Type Connector & Cable Accessories
The Standard Voltage 37-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution.Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 1.81kΩ
50-298-022
The 50-298-022 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 2 Amp MUX, Single 32-Channel 2-Pole
40-635-002
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
*High-Power Beam Profiling
Beam analysis of high-powered industrial lasers have always proved to be difficult because of the power levels (affecting the power densities) that these lasers operate at. Yet, the measurement of these lasers are critical for their success because of thermal effects which are more of a factor at these higher powers. These high-power performance measurement products have proven to be solutions for laser users who operate and maintain these high-powered lasers
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 0.5m, 500 Port
A500RMR-500RMR-0A050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-050
The 40-297A-050 (PXI) and the 42-297A-050 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Digital Incircuit Test
PFL780/760
The PFL780 and 760 use IC clips as a test interface. This makes them ideal for the service and maintenance of legacy systems. If you need to work on high density surface mount PCBs you should consider the GRS500 as a more suitable alternative.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
40-850A-114
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Rackmount Network Appliance
Axiomtek's 19-inch rackmount network appliance barebones with enclosure management capability, electromagnetically approved, and high density of Ethernet port, are suitable for various environments and applications. Axiomtek does not only provide high computing performance and reliable hardware platforms, but also provide system development kits for software integration.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode, 9/125 Fiber
40-855A-212-HI
The 40/42-855A-212-HI is a PXI/PXIe 2-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
4-Slot BRIC, 168x6, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-401-168x6
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-Slot BRIC 96x8 Matrix, 2A 2-Pole (4 sub cards)
40-565A-102-96X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI 12-Slot BRIC Matrix, 33x16 1-Pole (3 sub-cards)
40-562B-321-33X16
The 40-562B-321-33X16 is a high density BRIC12 matrix module with a size of 33x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 32-Channel, 2-Pole
40-614D-011
The 40-614D-011 (PXI) and 42-614D-011 (PXIe) 2-bank, 32-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector
42-153-004
The 40/42-153-004 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector.
-
product
PXI 12-Slot BRIC Matrix, 198x16 2-Pole (18 sub-cards)
40-562B-322-198X16
The 40-562B-322-198X16 is a high density BRIC12 matrix module with a size of 198x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
PXI 50 x SPST Ruthenium Reed Relay Switching
40-140A-021
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Non-destructive Asphalt Density Testing Equipment
PaveScan RDM
Geophysical Survey Systems, Inc.
The PaveScan RDM is ideal for uncovering inconsistencies that occur during the paving process, including poor uniformity and significant variations in density. By detecting these problems, PaveScan RDM helps to avoid premature failures such as road raveling, cracking and deterioration along joints.
-
product
Probecard testers
MANAGER
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
product
PXI 8 Slot BRIC 256x12 2A 1-Pole Matrix
40-597-108
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI 4-Slot BRIC Matrix, 88x8 1-Pole (4 Sub-cards)
40-562B-021-88X8
The 40-562B-021-88X8 is a high density BRIC4 matrix module with a size of 88x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Power Relay Module, 12xSPDT, 16 A, With Interlock
40-161A-101-HI
The 40/42-161A-101-HI is a PXI/PXIe 12xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
High Density Interface Card
PMC-A429HD
Alta Data Technologies’ PMC-A429HD interface card offers an unparalled 16, 32 or 48 channels of ARINC-429 on a single-width, front panel PMC module. The PMC card can be used in almost any PCI/PCIe based backplane system, and can encode or decode almost any ARINC-429 physical layer signal. The card can also support several 717 channels.
-
product
Relay
40-145-101
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI MUX 8 Banks of 16 Channel 1 Pole
40-610-022-8/16/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
PXI 8-Slot BRIC Matrix, 15x32 1-Pole (3 sub-cards)
40-562B-121-15X32
The 40-562B-121-15X32 is a high density BRIC8 matrix module with a size of 15x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Dual 2 x 2 Fibre Optic Mux MU
40-860-322
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI BRIC8 FIBO Matrix Dual 217x4 2pin brkout
40-592A-117
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
