-
Product
AC Electronic Load
IT8600 Series
-
IT8600 is ITECH latest series of AC/DC electronic loads with power range 0~14.4 kVA and adjustable frequency 45 Hz ~ 450 Hz. The unique oscilloscope waveform display function of IT8600's can display input voltage & current as waveform. It is equipped with measurement modes for different parameters such as inrush current, peak value, effective value, PF (power factor).
-
Product
PHIL System (Power Hardware In-Loop System) Case Study
-
In the PHIL (Power Hardware In-Loop) Case Study, the PHIL system consists of a PONOVO 4-Q amplifier, RTDS simulator, DC electronic load unit and PV inverter.
-
Product
GPIB User Installable Interface Module
EL34GPBU
Interface Module
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
6kW Regenerative DC Electronic Load (CC/CR/CV/CP/CC+CV/CR+CV)
PLZ6000R
-
PLZ6000R is a DC electronic load that regenerates load power to the AC line. Regular electronic loads consume load power by having semiconductor devices convert it into heat. By contrast, PLZ6000R converts load power into reusable electric power, rather than converting it into heat as is typically done, and feeds this power to the AC line, thereby substantially reducing the amount of waste energy. PLZ6000R is an environment-friendly electronic load that can contribute significantly to your energy saving efforts.
-
Product
High Power DC Electronic Load
3350G Series（4KW~6KW）
-
Each 3350G Series module has its own control and display panel, CC / CR / CV / CP /Dynamic modes, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
Load Banks
EL Series
-
*12kW, 15kW and 18kW DC Electronic Load*All of our Load Banks are continuously rated for Power and Current.
-
Product
Programmable DC Electronic Loads (conventional and regenerative)
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Low Voltage High Current DC Electronic Load
N62400 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
Product
DC Electronic Loads
-
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
Product
Programmable Single Channel DC Electronic Load, 150V/30A/200W
T3EL150302P
-
Programmable Single Channel DC Electronic Load, 150V/30A/200W.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
Modular DC Electronic Load
63600
-
Chroma Systems Solutions, Inc.
Chroma’s 63600 Modular DC Electronic Load is designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, adapters, and power electronic components. They are excellent for use in research, development, production, and incoming inspection applications. The 63600’s state-of-the-art design uses DSP technology to simulate non-linear loads using an unique CZ operation mode allowing realistic loading behavior.
-
Product
Programable Power Supply & Programable Electronic Load
EL-820P
-
*Digital button control and easy operation*High resolution(20mV, 10mA, 0.1W, 0.1Ω)*Overload prevention function*9 sets programmable memory*4 sets real time display*Voltage range: 1V~63V*Current range: 10mA~15A*Maximum power: 200W*Operation mode: CV, CC, CP and CR*Built in USB interface
-
Product
Electronic Loads
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
-
Product
Dynamometer
I-Series
-
AW I-Series dynamometers are excellent for diesel engine testing as well as other applications. The electronic load control system on this hydraulic activated dynamometer allows for precise and steady control of Power and RPM levels.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
-
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
Product
RFP DC Low Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
4kW Electronic Load
PT04-110
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Air Cooled Linear DC Electronic Load
ALx Series
-
The ALx Series utilizes conventional linear MOSFET-based dissipative elements, allowing the series to achieve a very wide voltage-current operating range within the model’s maximum power rating. Using the same heat management innovations developed for Magna-Power’s high density programmable DC power supplies, the ALx Series’ conservative cooling ensures long product life in environments up to 50 °C ambient operating temperature.
-
Product
Multifunctional DC Electronic Load (CC/CV/CR/CP)
PLZ-5W/5WZ Series
-
The PLZ-5W Series high performance electronic load is the successor to the highly respected PLZ-4W series, whilst still retaining the same high specification and build quality. Advances include a high visibility color display, low voltage operation from a minimum of 1 V to a maximum of 150 V. Programmable profiles of voltage/current can be applied (using the new ARB function, as used in LED/solar testing) in addition to the inherited 6 modes of operation: Constant Current, Constant Resistance, Constant Voltage, Constant Power, Constant Current + Constant Voltage, Constant Resistance + Constant Voltage.
-
Product
High Current Electronic Load (600W-1200W)
ELCH600 & ELCH1200
-
- Low lead resistance <5m Ohm for Fuel-cell- Battery Testing- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR- OV/OC/OP/OT protection- Communication: USB/RS232/GPIB
-
Product
PV-IV Solutions
-
We offer a broad range of PV IV Measurement systems for measuring solar cells from 3 mm to 300 x 300 mm. The wide range of solar simulators, vacuum chuck test stations, and electronic loads make it impossible to list “standard solutions” Most systems are put together for individual customer needs based on cell type and contact geometry of the devices being tested. Over the last several years we have designed and manufactured a wide range test solutions for many different types of cells and contact geometries. In most cases a customized solution is no more than a slight customization of a standard platform that has been previously designed.
