-
product
Super Low Noise Amplifiers
WCA Series
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
product
Low Pressure Cylinder Leak Tester
CLT4PB
Tests leakage at 35psi compared to 100psi in current leakage tester. Lower pressure prevents smaller bore cylinders from moving as they might under 100psi. Works well on small engines found in recreational, marine and other applications.
-
product
Frequency Multipliers
Triplers
*No mechanical tuners*fullband operation*planar design*zero Bias
-
product
Optical Probes - Low Bandwidth
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.*Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm*High-bandwidth DC up to 1.2 GHz*High Gain 1 V/mW*Low Noise <11 pW/√Hz*Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series*SONET/SDH and Fibre Channel Reference Receiver Performance
-
product
2-18GHz Instantaneous Frequency Measurement Unit
DR058-F2
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
-
product
1202a High Frequency Distribution
Precise Time and Frequency, Inc.
The ptf 1202A High Frequency Distribution amplifier provides high performance frequency references for laboratory or system use requiring distribution at frequencies of 30MHz and above.The ptf 1202A is especially designed to distribute the high frequency input signal to 12 separate outputs, with minimum signal distortion and maximum isolation between individual output signals.
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
Standard 0.80 (22.00) - 4.00 (114.00) High Frequency Probe
CSP-03G-003
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 3.70Return Loss @ -20dB (GHz): 1.80Nominal Impedance (Ohms): 50Dielectric VTE Rating (k VAC): 1Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,090Overall Length (mm): 27.76
-
product
Low Loss Cable Assemblies
True Blue
The Answer: An unmatched combination of low loss, durability, and value.The Question: What does Teledyne Storm Microwave’s True Blue® line of cable assemblies provide?For more than 30 years, our True Blue® assemblies have been the winning choice of design, test, and production engineers for:- Military and aerospace design-in applications- General purpose test applications- Production testing- With a design based entirely on high-performance materials, the True Blue® line covers frequencies from DC to 50 GHz.Assemblies are available in both custom configurations and a variety of standard lengths and connector combinations.The basic True Blue® cable is designed to be durable. However, for applications requiring added durability, assemblies are also available ruggedized, armored, and soft armored.
-
product
High Frequency Transformers
Osborne High Frequency Current Transformers operate at frequencies higher than 50/60 Hertz. Their purpose is to reduce high frequency system currents to lower values that are appropriate for instrumentation and/or protection circuits. They have been designed to meet specified current ratios, and burden impedance at a specified transformation error. One area of unique Osborne expertise is in designing for phase shift when high frequency current transformers are to be used for power measuring applications.
-
product
Low Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
product
E-Band Low Noise Amplifier MMIC
AWL-7186
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
product
Frequency Dividers
SMA SPDT electro mechanical RF relay switch features Indicators, Failsafe, Normally Open with an isolation minimum of 60 dB. SPDT electromechanical relay radio frequency switch PE71S6052 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our SPDT SMA coaxial RF relay electromechanical switch can ship worldwide the same day that it is bought as with our other available RF parts.
-
product
Frequency Extension Heads for Vector Network Analyzers
FEV
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
product
3207a GPS/GNS Frequency and Time Reference
GlobalTyme2
Precise Time and Frequency, Inc.
The ptf 3207A GlobalTyme2 GNS Receiver introduces a new level of advanced capability from a second generation, based on the highly successful ptf 3203A and ptf 3204A GlobalTyme receivers.The unit is both a frequency standard and a time standard and has been used as a precision frequency reference with low phase noise, in satellite communications applications around the world.
-
product
Universal Frequency Counter LXI, GPIB
53220A
For fast and accurate frequency and time-interval measurements, you need reliable devices in research and development. The Keysight 53220 universal frequency counter meets the requirements for this with its high accuracy, bandwidth and speed. Depending on the application and budget, choose one of the three available models. The connection to the PC is via USB, Ethernet/LXI or via GPIB.
-
product
Disciplined Frequency Standards
2960AR and 2965AR
The 2960AR has a rubidium timebase and provides two 10MHz and one 5MHz sine wave outputs. The 2965AR has a rubidium timebase and provides one 10MHz, one 5MHz and one signal generator output. The signal generator output uses Direct Digital Synthesizer (DDS) technology and is programmable from 100Hz to 50MHz via an RS232 serial interface. Both models can be disciplined by a 1pps input signal and provide a 1pps output. The 1pps input is typically provided by the GPS Frequency output from a device like a smart GPS receiver or antenna. The Novatech GPS1 Smart Antenna is available as an accessory to provide a complete turnkey solution.
-
product
Low Noise Converter for Radio Amateurs
The concept of software defined radios (SDR's) is becoming increasing popular in both commercial, military and Amateur Radio circles. In their basic form, the use simple front end filtering followed by a Quadrature Sampling Detector (QSD) with the post detection processing done in software using the sound card found in PC's. Several popular kits have been developed to introduce Amateurs to the concept.
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
Frequency Extension Calibration Kits
FEK
Farran’s FEK-xx-0001 calibration kit provides accurate calibration of the Vector Network Analyzer (VNA). It is compatible with TRL and SOLT calibration techniques and allows for a full 12-term port calibration.
-
product
Low Voltage EMC Standards Tester
LVTGO-VBS
LVTGO-VBS is a range of low voltage battery simulation units for robustness and EMC standards testing. It helps engineers to meet standards stipulated by a range of manufacturers, such as JLR, Ford, VW, BMW and Mercedes-Benz.
-
product
RFP DC Low Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Hydrogen Frequency & Time Standard
CH1-1006
The hydrogen frequency and time standard Ch1-1006 is designed to generate highly stable, high-frequency, spectrally pure sinusoidal 5, 10, 100 MHz and pulsed 1 Hz signals and for the behavior of time-frequency measurements.
-
product
Digital Frequency Meter
CSF-400
Measuring frequency. Accuracy: +/- 0.05%. 4 Digital display: 9999 Input Max. 400Hz/600 V, 30KHz/12V. Aux. Power AC 115/230V +/-15%, 50/60Hz. Isolation Aux. Power 12Vdc, 24Vdc, 48Vdc, 110Vdc available in option. Easy-to-wire, screw type terminal. Outside dimensions is DIN standard (96mm x 48mm) High stability & low cost.
-
product
Low Flow Protection Switch
Truflo
Parker Bestobell’s Truflo is an effective low flow protection switch that provides protection against flow changes that could be detrimental to equipment and processes. It provides a warning to operators of insufficient or excessive flow.
-
product
Impedance Analyser Frequency Response Analyser
C60
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
product
Frequency Converters & Transceivers
Mercury Systems’ converter and transceiver products are at the forefront of SWaP-optimized RF integrated products. Through substantial R&D investment and a library of building blocks, Mercury Systems has the capability to rapidly execute on the most complicated of custom transceiver designs. As the OpenVPX industry leader, Mercury Systems knows how to make integration into your system a breeze.
-
product
High Frequency Clock Divider Board
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
product
HF Low Noise Amplifier
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
