Filter Results By:
Products
Applications
Manufacturers
ATE Fixtures
Holding and positioning assemblies to guide UUT I/O access by automated test equipment.
See Also: Test Fixtures, PCB Test Fixtures, Board Test Fixtures
-
product
Lifts
Alum-a-Lift is proud to provide world-class material handling solutions for Electronics manufacturing, including a complete line of ATE lifts, ICT fixture lifts, and accessories.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
ATE
QT 200 NXG
Qmax Test Technologies Pvt. Ltd.
QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
RF ATE
IFF-7300S Series IFF/Crypto/TACAN Automated Test System. IRIS 2000/IRS 1200 ATE Software Revision Service. RF Expansion Module (RFEM).
-
product
ATE Connecting Solutions
C.C.P. Contact Probes Co., LTD.
Customized pogo towers with high frequency capability.
-
product
Test Fixture
OCP NIC 3.0
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
-
product
Avionics ATE Power Subsystem
AMETEK Programmable Power, Inc.
*Provides eight channels of programmable DC power with output isolation function*Output disconnect function*Total control via Ethernet within power supply.*Mounted in custom in transportable shock-mount case.
-
product
RWR ATE MKII
MS 1111
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Mechanical Benchtop Fixtures
500 Series
Hinged G-10 probe platesTooling holes for accurate drillingRemovable front and back panelsRigid fine grain G-10 plates for
-
product
Dielectric Test Fixture
16451B
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
product
Manual Fixture Kit
230376 – CMCSK-07-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
ATE Core Configurations
ATE Core Configurations streamline the design, procurement, and deployment of automated test systems with highly integrated mechanical, power, and safety system infrastructure. These off-the-shelf systems reduce lead times and simplify standardization and global deployment. Lower your total cost of ownership for your test systems with ATE Core Configurations.
-
-
product
Food Grips and Fixtures
AMETEK Sensors, Test & Calibration
We supply material testing instruments to some of the world’s most innovative companies within the food industry. The reason for this is our extensive experience within food testing, combined with our high precision texture analysis and packaging test systems.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Function Test Fixtures
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
product
Docking / ATE
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Floating bushings allow up to .04" of re-alignment. Use with a combination of various I/O modules and a max of 5,952 signal contacts simultaneously. The iDock series is rated up to 100,000 cycles.
-
product
Exchangeable Test Fixture
MA 2109/D/H/S-5
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
product
RF/Microwave ATE Systems
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
