Bus
One or more conductors or optical fibers that serve as a common connection for a group of related devices
See Also: Serial, Parallel, Bus Analyzers, Bus Adapters, Bus Converters, Bus Interfaces, Bus Translator, Extender Boards, Extender Cards, Cable Bus
-
product
PCIe Carrier Boards
These non-intelligent carrier cards interface XMC and PMC mezzanine modules and Industry Pack Modules to a PCI Express bus in a PC-based embedded computer.
-
product
Contact Resistance Meter
CRM 100C
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
product
PXI Express Board Virtex-5 ADC / DAC Module
SMT743
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc.
-
product
MIPI SLIMbus
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
product
CANbus Module
DS-MPE-CAN2L
The module implements a CAN protocol bus controller that performs serial communications according to the CAN 2.0A and CAN 2.0B specifications. The protocol uses a multi-master bus configuration for the transfer of frames between nodes of the network and manages error handling with no burden on the host processor. Error analysis features enabling diagnostics, system maintenance, and system optimization. A listen-only mode enables CAN bus traffic analysis and automatic bit-rate detection.
-
product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - XMC
Model 71664
- Complete radar and software radio interface solution- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
cDAQ-9171, 1‑Slot, USB CompactDAQ Chassis
781425-01
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
PID Controller
ZET 7190-R
ZET 7190-R — PID controller on CAN bus. It is used in automated systems for control signal forming.
-
product
PXI/PXIe Trigger Module
PXT1741
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
product
9 Slot, 3U PXI Express Chassis
GX7600 Series
The GX7600 Series mainframes are compact, 9-slot PXI chassis that can accommodate up to 8 instruments as well as an embedded single slot cPCI Express controller such as the GX7944 or a PXI Express external bus controller such as the x1 or x4 MXI - PXI Express interface. The GX7600’s compact 3U form-factor occupies only 9 x 18 inches of bench space, making it ideal for benchtop or space constrained applications. And when combined with 8 peripheral slots, integral Smart functions, and the bandwidth of PXI Express, the GX7600 represents a new level of performance, capabilities and value for PXI mainframes.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
ARINC 429 PMC Interface Module
PMC-429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
product
Hybrid Power Systems
UNIPOWER Hybrid Power Systems are designed to minimize power system life-cycle costs and carbon footprint. Power conversion components deliver leading efficiencies and maximum energy harvest from renewable resources using MPPT algorithms. A Hybrid Bus Architecture delivers available power from renewable resources supplemented by diesel generator or grid supply when necessary.
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
product
high-speed JTAG debugger
Bus Blaster v4
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
product
LXI WTB Terminator, 109.8 ohm
60-983-003
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
product
VXI Series
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
product
CompactPCI Serial 9 Slot 4U
The CompactPCI® Serial 9-slot chassis is based on the novel standard that relies on serial point-to-point interconnections. It overcomes the bandwidth limitation of the parallel CompactPCI bus and allows for PCI-E, SATA, USB, and Ethernet links among the cards. The chassis is a light-weight unit with powerful cooling and redundant power supplies. It perfectly suits a wide range of applications from lab usage to multi-system arrangement in a rack.
-
product
USB-8506 , LIN Interface Device
784664-01
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 57671
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
DynamicSignals/Gage Digitizer /Oscilloscopes for PXIe Bus
Wuntronic DynamicSignals/Gage Digitizer/ Oscilloscopes for PXIe Bus
-
-
product
InfiniiVision Oscilloscopes
1000 X-Series
50 MHz to 100 MHz See more signal detail with 50,000 wfms/sec update rate Make professional measurements, including mask, math, FFT, analog bus, and protocol triggering/decode Quickly learn how to use; Oscilloscopes have built-in help and training signals Educators can easily set up teaching labs with the free Educator’s Resource Kit
-
product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
CAN Logger
Reach Technologies' CAN Logger is a high performance, high channel count, DSP enabled, automotive bus data logger. The CAN Logger is ideal for capturing all or specific bus traffic for vehicles under test. The CAN Logger is also perfect for real-time monitoring of specific signals.
