-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
Portable Parallel Analyzer
SL1000
-
Perform up to four colorimetric and two probe-based measurements in parallel, and complete the entire test suite in 25% of the time. Complete more tests on site, get the results you need faster, and visit more sites in each shift.
-
Product
Parallel Electrode SMD Test Fixture
16192A
-
The 16192A test fixture is designed for impedance evaluations of side electrode SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1(L)[mm].
-
Product
GPIB Parallel Interface
Model 4803
-
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
Parallel Seam Sealers
-
It is an equipment to hermetically seal the packages, such as the crystal and SAW devices, optical devices, sensors, MEMS, etc., by seam welding. Hermetic sealing can be accomplished in both N2 and vacuum environment. Furthermore, we are offering a variety of products for research and development and production applications.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
Parallel Simulation Engine
RocketSim
-
Complementing compiled-code simulators, Cadence® RocketSim™ parallel simulation engine eliminates functional verification bottlenecks by speeding up simulation using commonly available multi-core servers.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
-
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Parallel systems
-
Did you know you can couple several Gill AC, Gill 12 and Weld Testers together or any combination of Gill AC, Gill 12 or Weld Tester, to give you a parallel logging multiple Potentiostat / Galvanostat / ZRA / FRA system, capable of recording from each working electrode at up to 60 readings per second. Coupling several Gill ACs or Gill 12s together gives the added abilities of the Weld tester and the ability to perform fast sweeps. Using our latest software, it has never been easier to couple instruments together to provide a Parallel System. In fact up to 32 instruments can be controlled at the same time. These instruments can either have individually enclosures or be rack mounted.
-
Product
Parallel NTDS Isolation Tap Box
-
IXI’S NTDS parallel isolation tap box is the ideal solution for relibility tapping NTDS parallel type A, B, C, and H interfaces. It connects easily to existing cables forming a tee connection that can be used for data monitoring and acquisition over long distances without interference with your system.
-
Product
Parallel Plate Dielectric Test Cell
LT-4203A
-
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
Product
"Soft Grid" and Parallel Operation AC Generator Excitation Regulator
svrsp
-
The Kinetics model SVRSP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the DC fields on an AC generator operating in parallel with other AC generators and the power system is a "soft system" in relation to loading. A "soft system" is a generating system that may not be able to sustain the rated AC voltage under impulse/step loading conditions and results in voltage reduction when tan impulse/step load is applied.
-
Product
"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator
SVRFP
-
The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.
-
Product
Parallel Active Multifunction Filter
SINAF 3.0
-
Lifasa - International Capacitors, SA
The active filters offer the best possible solution to solve the problems related to the quality in the electrical network, both in industrial three-phase installations, as commercial or service installations. These problems are caused, not only by the harmonics, but also by the consumption of reactive power (generally of capacitive type).
-
Product
Massively Parallel Board Test System
I7090
-
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
Product
Parallel Interface Voltage Output D/A Converters
-
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
-
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Dual Parallel Strain Gauges
-
Dual Parallel Strain Gauges strain gauges have two measuring grids arranged parallel to each other. Typical applications include measurements on bending beams
-
Product
LCR Meter
-
*Rs, Rp, Cs, Cp, Ls, Lp, phase angle, Dissipation factor, Quality factor *Auto select series or parallel test mode *Auto select 100Hz/1kHz/10kHz test frequency, 0.5V rms approx. *Calibration
-
Product
Switch Mode Power Supplies-Water Cooled
-
The MSW Rectifiers are based on Switch Mode Technology. This reliable technology assures excellent quality DC currents with a ripple of < 3% and a control accuracy of less than 1%.The MS-Series features constant voltage and current control with easy, quick installation and maintenance. Modular versions easily increase the output by means of series or parallel connection. All models have DC short circuit protection. With forced air-cooled models, the cooling air quantity is controlled in relation to the load reducing contamination and noise levels.
-
Product
Geometrical Measurement Software
-
PRÜFTECHNIK Condition Monitoring GmbH
Activate your machinery more quickly, and help it run longer. PRÜFTECHNIK geometric laser alignment tools and software enable you to easily check and adjust your machine geometries for: straightness, flatness, level, inclination, plumbness, parallelism, and right angle check. Our tools are powerful, precise, and easy to use on a vast range of machinery—they can measure for the most demanding alignment jobs, including a bore of almost any diameter, and/or any surface type or inclination. Find the right geometric measurement tool for your machines.
-
Product
Hybrid & Electric Vehicle Dynamometer Testing
-
SAKOR Technologies Hybrid/Electric Vehicle Powertrain Dynamometer Test System (HEViDyne), winner of the SAE 2008 Technical Award for Hybrid/Electric Vehicle Testing Technology, is a comprehensive solution for performance, efficiency, and durability testing of all types of hybrid and electric vehicle drivetrains, including:*Hybrid assist (parallel hybrid)*Gasoline or diesel/electric (serial hybrid)*Fully electric vehicles
-
Product
CSvideo | CTvideo | CSvision Series Infrared Thermometer
-
The video pyrometer series optris CSvideo/CTvideo and the new innovative ratio pyrometer CSvision allow a parallel use of video and crosshair laser aiming for an optimal measuring field adjustment even in processes with limited access. They reliably measure temperatures of metals or ceramics and, due to their short measuring wavelength, reduces measuring errors of surfaces with low or unknown emissivities. The high quality video sighting can show its full advantage together with the software CompactPlus Connect or the IRmobile App on your cell phone with state-of-the-art zoom and image rotation features. The adjustable focus, motorized on CSvision, allows an optimal adaptation to different application and installation demands. As CSvision can measure objects up to 3000 °C a unique two-step brightness reduction filter (BRF) is giving the user a tremendous advantage when aiming on hot and extremely bright objects.
-
Product
Scale / Weight Meter
-
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
Product
Test Database Software Module
-
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
Product
USHIO Blue Violet Laser Diodes (375nm - 405nm)
-
The Optoelectronics Company Ltd
The USHIO HL40071MG is a single transverse mode 405nm laser diode which offers 300mW optical output power in a 5.6mm package with typical optical and electrical characteristics, (Tc=25 degrees C, cw), of 50mA threshold current, operating current of 280mA, operating voltage 6.0V, 6 degrees beam divergence parallel to the junction, 15 degrees beam divergence perpendicular to the junction, laser diode reverse voltage of 2V and operating temperature of 0 to +70 degrees C.
-
Product
Force & Strain Measurement
-
Load cells, tank weighing devices, balances, scales, force gauges, torque sensors and strain gauges including diaphragm, dual parallel, linear, rosette, T-rosette, and torsion and shear types.
-
Product
150~300W DC Electronic Loads
JT631 Series
-
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
Multiplexers (MUX)
WDM
-
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
