High-Pass Filters
Refine signal, allowing the transmission of signal above a specific corner frequency, while strongly attenuating the frequencies below.
-
Product
Anechoic Chamber Filters
-
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
-
Product
Filtered Analog Input Expansion Board
MSXB 048
-
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
Product
Filter Building Blocks
-
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS800
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations.
-
Product
Capacitor for DC Filtering
FIL1
-
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple and protect the line from instantaneous peaks and surges of tension.
-
Product
RF Filters
-
RF Filters block unwanted frequencies when testing electronic devices for emissions during EMC testing. They attenuate unwanted frequencies and allow the desired signals through. The RF filters isolate the device under test from external RF noise, this increases the reliability and accuracy of the EMC testing by preventing out-of-band noise and harmonics.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
CAT-5 Video Variable Filters
-
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
Product
Band Pass Filters
-
VDI offers up-converter modules for communication applications. The double sideband nature of the up-converter modules makes filtering necessary. VDI has designed filters to filter one sideband and preserve signal modulation. These filters offer low passband insertion loss and high out-of-band rejection. Custom filters may be available upon request. NRE (non-recurring engineering) fee may be required.
-
Product
Fabry-Perot Based Scanning Filter
-
This new type Fabry-Perot Based Scanning Filter (FPSF) is based on Optoplex proprietary fiber optical Fabry-Perot Etalon technology. It offers F-P based scanning filter with central wavelength at 1060nm, 1310nm, 1550nm or other customized wavelength. It can be tuned manually or automatically by scanning over a wide spectral range from 10nm to 100nm with bandwidth from 0.05nm to 1.0nm. FPSF features less than 3dB insertion loss and as high as 1kHz scanning frequency. Its unique high reliability and low insertion loss design presents the most cost-effective solution for OEM application from telecommunication to fiber sensing interrogation.
-
Product
Capacitor for AC Filtering
PECA4 (440V)
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
Product
Tunable Filters - Digitally Controlled
-
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422, BCD, ARC171, ARC234, Ethernet, USB or "Thumbwheel" panel mount.
-
Product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
-
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Bandpass Filters
-
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
Product
Gas Filter Correlation Carbon Monoxide Analyzer
Model T300
-
The Model T300 measures low ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 14 meters. The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing extreme sensitivity. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information, is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
-
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input W/ Digital Filter And Interrupt PCIe Card
PCIE-1761H
-
8 opto-isolated digital input channels8 relay actuator output channelsInterrupt handling capability for all DI channelsSelectable Digital filter time for all DI channelsOutput status readableLED indicator to show activated relaysSelectable Form A or Form C
-
Product
Individual Optical Filters
-
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS1000
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Dual 10th Order Lowpass Filter
64-VBF
-
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
Product
Telephone Attenuators & RFI Filters
-
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
-
Product
16-Ch Relay And 16-Ch Isolated Digital Input W/ Digital Filter & Interrupt PCIe Card
PCIE-1762H
-
16-ch digital input and 16-ch relayInterrupt handling capability for all DI channelsSelectable Digital filter time for all DI channelsOutput status readableLED indicator to show activated relaysSelectable Form A or Form B
-
-
Product
15 Amp 120 VAC Filter and Surge Arrestor
AS-AC15
-
- 15 amp 120VAC quad outlet for high power devices- Resettable circuit breaker protection, easy to use and reset- I EA standard input plug and #14 GA AC line cord for USA - standard interface- MOV surge arrestors included - for even more protection- High level of common mode and differential mode filtering digital noise and RF filtering eliminates- digital artifacts and RF interference - See chart- Front Panel Neon Blue AC ON indicator - just plain cool to look at, not too bright!- Double shielded box inside - for optimum filtering operation- Size 6W X 4H X 4 3/4 D in inches approx 3 lbs
-
Product
Active Filter
J2190A
-
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
Product
Low-PIM, Low-Power Filter Solutions for Monitoring Broadband Emissions
-
Bandpass/Bandstop, Notch, and HighpassCompact Design for Rack Mounting of Several BandsSuitable for Monitoring Emissions from Semiconductors,TX/RX Chipsets, SAW/BAW Filters, Cell Phones,Printers, PDA’s, etc.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations
-
Product
Rack Module with Standard Contactors with Anti-Harmonic Filters
MODF Rack
-
Lifasa - International Capacitors, SA
The MODF-RACK control units include, in a compact form, all the components necessary for the operation of a step of a capacitor bank with filters. MODF-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
EMI/EMC Filters And EMI Solutions
-
Chengdu Mengsheng Electronics Co., Ltd.
DOREXS is a company specializing in the manufacture of EMI/EMC filters. For more than a decade, it has been committed to providing cost-effective EMI/EMC filters and EMI solutions for commercial, medical, military and industrial applications. We help your equipment gain recognition for its stable and reliable functions.
