High-Pass Filters
Refine signal, allowing the transmission of signal above a specific corner frequency, while strongly attenuating the frequencies below.
-
Product
Signal Acquisition and Filtering Technology
SNAPTrack®
-
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
Product
Harmonic Filters
-
ENTES Harmonic Filter Reactors are used in serial connection with capacitor banks in power factor correction units. By using these types of detuned reactors it is possible to increase the capacitor impedance against harmonic currents and to keep the resonance frequency under the frequencies in which main harmonic currents occur by shifting the resonance frequency.
-
Product
Light Measurement Optical Filters
-
International Light Technologies
Optical filters are often used to attenuate certain wavelengths of light and produce an overall desired detector response.
-
Product
Narrow Band Filters (Single Octave)
MINI-SMT® Series
-
The new MINI-SMT™ tunable filter advances our popular MINI-POLE® Series by providing Surface Mount (SMT) capability along with the field proven RF power handling, low distortion and exceptional selectivity performance of our MINI-POLE® filters. MINI-SMT™ bandpass options are available from 700 MHz to 3 GHz.
-
Product
Filter Test System
DU7216/7218
-
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
SIM Filter
-
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
-
Product
Optical Filters
-
INPHORA offers calculation, development and production of unique Optical Filters designed to match exactly to the requested parameters or to fit to the given application.
-
Product
Filters and Compiners
-
Combine four bands to a common line Multiple broadband configurations, including AWS High power handling with low IM and insertion loss AISG 2.0 compliant
-
-
Product
Narrow Band Filters (Single Octave)
POWER-POLE® Series
-
The POWER-POLE® Series of tunable filters provides improved RF performance with increased power handling capability and the lowest insertion loss for a given bandwidth. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the POWER-POLE Series Selection Guide.
-
Product
Gas Filter Correlation CO Analyzer
Model N300
-
Teledyne Advanced Pollution Instrumentation
The Model N300 is a microprocessor-controlled analyzer based on the Beer-Lambert law that is used to determine the concentration of carbon monoxide (CO) in a sample gas.The N300 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb Infrared (IR) light. The analyzer passes the IR light beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
Product
Air Core Harmonic Filter Reactors
-
Use of nonlinear loads such as power electronics based equipment and electric furnaces have been on the rise for the last decades. Such loads decrease the power quality of the network that they are connected to. One of the most important parameters for defining the power quality is harmonic distortion.
-
Product
16-Ch Relay And 16-Ch Isolated Digital Input W/ Digital Filter & Interrupt PCIe Card
PCIE-1762H
-
16-ch digital input and 16-ch relayInterrupt handling capability for all DI channelsSelectable Digital filter time for all DI channelsOutput status readableLED indicator to show activated relaysSelectable Form A or Form B
-
Product
RF Filters
-
CTS develops and manufactures high-end radio frequency (RF) filters used by various technologies to block out or filter certain signal frequencies. In 1982, CTS invented the ceramic monoblock, and ever since, our ceramic RF filters have been setting the industry standard in terms of lowest insertion loss, attenuation /rejection/isolation, Q-factor, size, power handling, and transition slope. Our portfolio includes band-pass filters, notch filters, low-pass filters, delay line filters, diplexers, duplexers, and triplexers/multiplexers.
-
Product
Filtered Analog Input Expansion Board
MSXB 048
-
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
Product
Switch Filter Bank
-
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
Product
LCL Filters
-
LCL Type Harmonic Filter Modules are used to filter out the input current harmonics of the Motor Drives having six-pulse diode/thyristor rectifiers, where harmonic current distortion exceeds the limits defined in standards.
-
Product
Bandpass Filters
-
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
15 Amp 120 VAC Filter and Surge Arrestor
AS-AC15
-
- 15 amp 120VAC quad outlet for high power devices- Resettable circuit breaker protection, easy to use and reset- I EA standard input plug and #14 GA AC line cord for USA - standard interface- MOV surge arrestors included - for even more protection- High level of common mode and differential mode filtering digital noise and RF filtering eliminates- digital artifacts and RF interference - See chart- Front Panel Neon Blue AC ON indicator - just plain cool to look at, not too bright!- Double shielded box inside - for optimum filtering operation- Size 6W X 4H X 4 3/4 D in inches approx 3 lbs
-
Product
Filter Building Blocks
-
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
Product
Programmable, 2-Channel Low-Pass Filter Module
AAF-3F
-
Programmable, 2-Channel Low-Pass Filter Module. The AAF-3F is designed for use with the AAF-3M and AAF-3PCI filter boards.
-
Product
LV Iron Core Harmonic Filters
-
Nonlinear loads such as power electronics based equipment and electric furnaces are sources of harmonic currents leading to harmonic distortion, which is one of the most important parameters for defining the power quality. Most of the commercial loads such as personal computers, photocopy machines, power supplies, and compact fluorescent lamps; and industrial loads such as AC and DC motor drives inject harmonic currents into the network that they are connected to.
