JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
Product
Low Cost Emulator
EB-XAG3
-
# Emulates P51XG1/2/3x Microcontrollers# Real-Time Operation up to 30MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C and Assembler# MS-Windows Debugger Software# Reduced Set of C-Compiler and Assembler# Support for ROMless and ROMed Microcontrollers# 64K of Code Memory# Performance Analyzer
-
Product
Smart Network Emulation for All Mobile Device Tests
CMWcards
-
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
Product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
Controller
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
Product
Low Cost Emulator
EB-XAS3
-
* Emulates P51XAS3x Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 68-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
WAN Simulator / Emulator
LANforge ICE
-
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
Product
PCI Based JTAG Controller
PCI-1149.1/Turbo
Controller
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
Product
Lightning "Emulator" Shield
SEN-39002
-
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
Product
Emulator
-
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
Product
PD Emulation Module
-
Xtramus Industrial Instruments
A specialized hardware testing tool made by Xtramus Industrial Instruments that acts as a Powered Device (PD) to test Power over Ethernet (PoE) equipment.
-
Product
Adjustable ISI Channel Emulation Package for M8000 Series BER Test Solutions
M8070ISIB
-
Simplify receiver testing by offering unprecedented flexibility for handling test channels.
-
Product
Satellite and AerospaceChannel Emulation Toolset
S8825A
-
Satellite, aerospace, and airborne radio link testing with realistic wireless propagation conditions. 5G NTN test support with satellite connection from mobile phones. Interconnecting networks for full end-to-end system testing.
-
Product
Network Emulator
Calnex SNE-X
-
A multi-port, high-performance network emulator to drive product/application quality and reduce the cost of test with rigorous, scalable test capability.
-
Product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
Controller
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
Product
JTAG Isolation Protection
-
Our line of JTAG isolators help protect your investment in computers, development boards, debug probes, and lab equipment. Each model connects easily between your target board and debug probe.
-
Product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
-
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
Product
Wireless Network Emulators
-
Keysight’s industry-leading range of wireless network emulators and device test solutions enable the entire mobile device ecosystem to accelerate the market introduction of new wireless devices by streamlining the workflow from early prototyping, development, and design verification to conformance, carrier acceptance, and high-volume manufacturing.
-
Product
JTAG External Modules (JEM) DIMM/SODIMM Socket Cluster Test
-
The primary function of the JTAG External Modules (JEM) for the DIMM/SODIMM Socket Cluster Test is to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system and to strengthen the memory-independent JTAG testing for the assembly correctness of the almost full spectrum of the modern socket types, particularly (according to JEDEC_Std.21-C):
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
high-speed JTAG debugger
Bus Blaster v4
-
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
Product
OC-3/STM-1 And OC-12/STM-4 Analysis And Emulation Card(w/ GigE And USB 2.0)
LightSpeed1000™
-
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames. GL's LightSpeed1000™ hardware platform (PCIe Card and USB Pod) is capable of OC-3/12 and STM-1/4 wire-speed processing on quad optical ports for functions such as wire-speed recording and wire-speed playback of Unchannelized and Channelized ATM, PoS, and RAW Traffic.
-
Product
Network Cable Emulator
-
Xtramus Industrial Instruments
A specialized hardware test device manufactured by Xtramus Technologies that simulates real-world physical and environmental network conditions on Ethernet links.
-
Product
Network Emulator
KMAX
-
The KMAX network emulator helps network engineers test and measure performance in order to identify and remove defects. Network emulators turn well behaved development and test networks into the kind of slow, congested, and less-than-reliable services encountered on the internet. In addition, unlike the real internet, network emulators allow the operator to control these conditions so that products and apps can be subjected to controlled and repeatable tests, by routing selected packets through a series of impairment nodes.
-
Product
PoE Testing/ PD Emulation
-
Xtramus Industrial Instruments
A hardware and software test solution used to evaluate Power over Ethernet (PoE) equipment by mimicking real-world powered devices like IP cameras or VoIP phones.
-
Product
JTAG Boundary-Scan Controller for PXI and PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37x7/PXI
Controller
High speed and performance JTAG Boundary-scan controller for PXI and PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
Product
Air Interface Emulator
-
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
-
Product
JTAG Debug Probe for Cortex-M
J-Trace PRO
-
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
Product
T400 Radar Emulation Simulator
-
Kratos Defense & Security Solutions, Inc.
The Radar Emulation Simulator provides a cost-effective solution for simulating targets and channel effects in an RF environment. The system can be controlled via a standalone graphical user interface for simplified scenario applications, a dedicated real-time interface, or remotely via the Ethernet interface.
-
Product
Low Speed Protocol Decode/Trigger Software (I2C, SPI, RS232, I2S, JTAG)
D9010LSSP
-
This bundle includes powerful decoding and triggering for the following serial bus standards: I²C, SPI, Quad SPI, eSPI (including Quad eSPI), RS232/UART, Manchester, I²S, SVID, and JTAG (IEEE 1149.1). It is compatible with S-Series, V-Series, Z-Series, EXR-Series, MXR-Series, UXR-Series, 9000 Series, and 90000 Series Infiniium oscilloscopes. For detailed information on the decode and trigger settings, please refer to the datasheet.
-
Product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
Controller
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
