JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
Product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
Controller
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Sensor Signal Emulator
-
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
Product
Network Emulator
Calnex SNE-X
-
A multi-port, high-performance network emulator to drive product/application quality and reduce the cost of test with rigorous, scalable test capability.
-
Product
10G Ethernet Emulator
VirtualNetTM XG
-
VirtualNet-10G is a high-performance Network Emulator that replicates real world Ethernet network effects such as latency and errors on user traffic in a controlled environment. The VirtualNet-10G emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualNet-10G emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
Regenerative AC Emulator, 1200 VAC, 32 A, 45 KVA, 3‑Phase
SL1212A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 1200 VAC, 65 A, 90 KVA, 3‑Phase
SL1213A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Testing Solution & Battery Emulation
PLUTON
-
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
Product
JTAG Probe
MAJIC
-
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
Product
Scienlab Dynamic DC Emulator
SL104XA Series
-
The Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
Product
high-speed JTAG debugger
Bus Blaster v4
-
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
Product
Terminal Emulator
Distinct IntelliTerm
-
Distinct IntelliTerm is a terminal emulator that allows you to access data on diverse corporate information servers such as IBM mainframes, IBM AS400, UNIX and VAX systems from a single application. It includes full featured terminal emulation for TN3270E, TN3270 for Type 3278 and 3279, with support for 3179G, 3192G, 3472G and 3279 S3G graphics, TN5250 and VT52 through VT420. Distinct IntelliTerm operates over the Telnet protocol running over TCP/IP, an area in which Distinct is a market leader. Distinct IntelliTerm integrates related utilities such as multi-connect FTP with SOCKS proxy support, print server support with LPD and 3287 printing support, substantially reducing your training and support costs.
-
Product
Transient Suppression for Corelis JTAG Controllers
TAP Protection Adapter
Controller
Transient events such as Electrostatic Discharge (ESD), inductive switching, and lightning can damage electrical equipment, leading to costly repairs and test equipment down-time, reducing production capacity and increasing time-to-market.The Corelis TAP Protection Adapter is designed to enhance protection to any Corelis JTAG controller, shielding against harmful events using a combination of electrical defenses.The compact adapter features series resistors and transient voltage suppressor (TVS) diodes to mitigate damage to the JTAG controller. Protect your investment and enjoy peace-of-mind with the TAP Protection Adapter.
-
Product
JTAG Boundary-Scan Controllers for High-Volume Production Systems
-
Corelis has designed special hardware that autonomously performs concurrent (gang) testing and programming of multiple units without additional user intervention. The entire testing and programming, including on-the-fly verification of results, is done in modular and expandable hardware.
-
Product
Protocol Emulations
-
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
Product
WAN Simulator / Emulator
LANforge ICE
-
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
Product
JTAG Boundary Scan Tools
-
Blackhawk has teamed with Corelis, an EWA company, to offer customer Intuitive and High Performance JTAG Boundary Scan Tools that are compatible with our JTAG emulator product line. This allows developers not only to debug code on TI devices but also leverage boundary scan testing using the same emulator hardware.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation
66319B
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
Product
In-Circuit Emulator
DS-XA
-
* Emulates XA Derivatives * 2MByte Code and Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 30MHz @ 5V * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software for Windows NT and 95 or Later * 3.3V And 5V Emulation Support * Support for ROMless and ROM Microcontrollers * PLCC Emulation headers
-
Product
Emulation of the Mobile Wireless Environment from 2G to 5G
Base Station Emulator sUTP 5018
-
Bring a whole mobile network to your lab or production: NOFFZ Base Station Emulator (BSE) creates a customized cellular wireless environment. This makes testing wireless devices easier than ever before.Compact, cost-effective testing of multiple DUTs in parallel from 2G to 5G, including endurance testing for several days.
-
Product
Virtual Network Emulator
NetropyVE™
-
NetropyVE™ is the virtual edition of the Netropy network emulator. It offers advanced capabilities to benchmark, troubleshoot, and optimize the performance of critical applications in virtualized test environments. Every virtual machine can be assigned a unique WAN access profile, and then controlled to insert latency, jitter, packet loss, and congestion. Simulate Bandwidth, Latency & Jitter, Loss.
-
Product
Low Cost Emulator
EB-C251
-
# Real-Time and Transparent C251 Emulation# supports Intel MCS?251 and Atmel/W&M/Temic C251# Uses Bond-Out Technology# Maximum Frequency Support up to 24MHz# Source-Level Debugger for C, PLM and Assembler# MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 256K Internal Memory# Memory Mapping Capabilities# Real-Time Trace
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
Network Emulator
-
With Simnovus Network Emulator, it is easy to validate if your device works on networks across any region in the world under different network configurations. It supports carrier bandwidth up to 100MHz and frequency ranges from 70MHz to 6GHz for both FDD and TDD. And thanks to the software-based radio (SDR) design, you can also verify custom bands including CBRS.
-
Product
Low Cost Emulator
EB-51
-
# Emulates 80C51 Microcontrollers and Derivatives# Real-Time Operation up to 40 MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C, PLM and Assembler# DOS and MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 64K of Code and 64K of Data Memory# Data Memory with Mapping Capabilities# Performance Analyzer# Real-Time and Conditional Breakpoints
-
Product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Controller
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
Product
Low Cost Emulator
EB-XAG3
-
# Emulates P51XG1/2/3x Microcontrollers# Real-Time Operation up to 30MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C and Assembler# MS-Windows Debugger Software# Reduced Set of C-Compiler and Assembler# Support for ROMless and ROMed Microcontrollers# 64K of Code Memory# Performance Analyzer
-
Product
Scienlab Regenerative 3‑Phase AC Emulator
SL1200A Series
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
Controller
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
