Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Signal Transformers
-
Signal transformers are used as a step-up / step-down, isolating, or impedance matching component in electronic devices.
-
Product
Connect PT100/PT1000 Sensors To Output A Voltage Signal
K- PT100/1000
-
Our K-PT module is designed to connect up to PT100/PT1000 sensors and simply provides an output voltage signal. Thus enabling the most standard voltage measurement devices to work with PT100/PT1000 sensors. The PT100 sensors offer excellent accuracy and repeatability.
-
Product
Portable DAQ & Signal Analyzer
ObserVR1000
-
Vibration Research Corporation
Collect data with the press of a button using the battery powered ObserVR1000 hardware and a mobile interface. Stream to the SD card while running other test modes, or use independently as a field data recorder and analysis package.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder
610110125
Signal Contact (Receiver)
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder.p/n 610110125 TriPaddle Receiver 50µ" AU platingp/n 610110101 TriPaddle Receiver 30µ" AU platingThis contact primarily used in CASS applications.
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
Signal Analysis
Histograph
-
The Histograph software is used for statistical signal analysis: finding the statistical values characterizing the signal and building the theoretic histograms based on the data obtained.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 44 GHz
N9961B
Signal Analyzer
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
-
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Single Ended (5 Amps)
7-124922000-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Single Ended (5 Amps).
-
Product
Photo-Frame Style Smart Signal Detective Jammer
WF-DJ7
-
Shenzhen Tangreat Technology Co., LTD.
WF-DJ7 is a Painting Smart Signal Jammer.WF-DJ7 is designed mainly used for indoor cellphone signal detection and shielding, such as meeting rooms,border control units, Border Patrol and Drug Enforcement, Customs, Houses, Churches, Courts, Theaters, Offices,classrooms. checkpoint personnel, Hospitals, Recording Studios, Banks, Contract Tendering Rooms, Testing Facilities, Security Services, Military Units, Secret Services, News Conference Scene, Libraries, Museums,Prisons and so on.
-
Product
Frequency Converter Characterization With Wideband Modulated Signal
N5245BQ
Network Analyzer
The N5245BQ provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements
-
Product
RF Signal Generator
-
RF Lambda’s RF signal generators are wideband DDS driven signal sources in a variety of frequency ranges. They offer extremely fine frequency step size and low phase noise as well as output level control. They are easy to configure with the included GUI and USB interface. They are AC powered for convenience.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Analog Signal Conditioning &Isolation Products
DSCIA
-
DSCIA module is a signal channel isolated analog input or output.
-
Product
Digital and Mixed-Signal Test Solutions
-
A digital device processes electronic signals that represent either a one (on) or a zero (off). The ‘ones’ and ‘zeros’ represent data. Each one or zero is referred to as a bit and a group of 8 bits equals a byte
-
Product
PXIe-5820, 500 MHz, 1 GHz I/Q Bandwidth, Baseband PXI Vector Signal Transceiver
783967-01
Vector Signal Transceiver
500 MHz, 1 GHz I/Q Bandwidth, Baseband PXI Vector Signal Transceiver—The PXIe‑5820 is the baseband model of the second-generation vector signal transceiver (VST) with 1 GHz of complex I/Q bandwidth. It combines a wideband I/Q digitizer, wideband I/Q arbitrary waveform generator, and high-performance user-programmable FPGA in a single 2-slot PXI Express module. You can use the VST for a variety of applications including baseband I/Q test of wireless and cellular chipsets; envelope tracking of digitally predistorted waveforms for power amplifiers; and the generation and analysis of new wireless standards such as 5G, 802.11ax, and LTE-Advanced Pro.
-
Product
Blanking Signal Generator II
MS 1609
-
This System used for generating continuous and pulsed variable power outputs (Voltage).
-
Product
Clock Signal Generators
-
Optellent offers a range of clock signal generators providing clean reference clock signals up to 32 GHz.
-
Product
PathWave Vector Signal Analysis Software
89600 VSA
-
A comprehensive set of tools for demodulation and vector signal analysis.
-
Product
PXIe-5672, 2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator
779900-03
Vector Signal Generator
2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator —The PXIe‑5672 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5672 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee.
-
Product
100MHz Signal Generator
DDS8m
-
The DDS8m generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The DDS8m is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. SOF8 windows software is available as an extra cost accessory.
-
Product
Signal Level Meters
-
PeakTech Prüf- und Messtechnik GmbH
In the field of Cable TV, Broadcast TV, Satellite TV and the distribution of these signals there are several different types of meters used to measure the signal strength and or quality.
-
Product
Radio Monitoring and Signal Analysis
-
Shoghi has a full portfolio of products which fulfill the customer requirements for radio monitoring and signal analysis. Shoghi has a very robust SDR based wideband radio monitoring solution which can be implemented both in static or mobile versions for HF and VHF/UHF frequency bands. The Shoghi Radio Monitoring and DF system is the full-fledged product which provides the facilities for wideband signal reception and advanced signal analysis capabilities in addition to both wideband and narrowband D capabilities. The signal analysis capabilities include the ability to demodulate and decode both narrowband and wideband signals and advanced signal protocol analysis for detection of specific data protocols used in the intercepted RF signals.
-
Product
Signal Analysis
Modal Analysis
-
Modal Analysis is used for analyzing pulse and transition characteristics of signals coming from the input channels of FFT spectrum analyzers and seismic stations in real time or recorded time realization view mode.
-
Product
Mixed Signal Oscilloscope: 70 MHz, 2 Analog Plus 8 Digital Channels
MSOX2002A
Oscilloscope
70 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Signal Generator
-
An electronic device that generates repeating or non-repeating waveforms used to test and evaluate electronic test equipment.
-
Product
Portable RF Signal Generator
ACE 5400
-
The ACE 5400 portable RF signal generator has four carriers that can be activated individually or in any combination. Each frequency and amplitude is adjustable by the user. The ACE 5400's basic and straight forward performance is perfect for applications that require a precise, stable RF stimulus. Applications: Testing and aligning CATV return bands; Great for institutional networks.
-
Product
Signal Architect Simulator Software
GNSS
-
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
