-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Waveguide Rotary Joints
-
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Flexible Waveguide
-
Flann offers a number of solutions for flexible waveguide interconnect including waveguide-coaxial-waveguide and semi rigid. Traditional flexible waveguide solutions are available on request.
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (f) To WR-12, 60 To 90 GHz
E281CS
-
E281CS E281CS In-line 1.0 mm (f) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Double Ridged Waveguide Horn
DRH203
-
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
Product
Waveguide Bends
-
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
Product
Waveguide Probes
-
We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.
-
Product
Manual Attenuator (Waveguide)
-
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
-
Product
Double Ridged Waveguide Horn
DRH18–E
-
Frequency range: 1 GHz -18 GHz VSWR (max / AVG): < 3:1 / 1.35:1Impedance: 50 O (Ohm)Connector: SMA female / N femalePower (CW / Peak): 50 W / 100 W
-
Product
Double Ridged Waveguide Horn
DRH20E
-
Frequency range: 1.6 GHz - 20 GHz VSWR (max): < 1.5:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 50W / 100 W
-
Product
Waveguide To Coaxial Transitions
-
Waveguide to coaxial transitions are an integral capability of the business. TRAK offers a choice of connector type and orientation, pin/socket interfaces to waveguide apertures with a choice of standard or custom flange details.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 50 to 75 GHz
V281C
-
The Keysight V281C is a 1-mm female to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The V281C is used with the Keysight 8510XF systems.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
-
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
Product
10 dB V-Band Waveguide Directional Coupler for Test Labs
SWD-5038531040H-15-SB
-
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
-
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
-
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
Waveguide Harmonic Mixers (smart mixer), 75 to 110 GHz
M1970W
-
The Keysight M1970W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of N9030A PXA, N9020A MXA,and N9010A EXAsignal analyzers up to 110 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Double Ridged Waveguide Horn
QRH0140
-
Frequency range: 1 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 10 W / 20 W
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
-
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
