-
Product
HD-TVI Tester, HD-CVI Tester, AHD Tester
M-IPC-300 series
-
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
Bench Hardness Testers
-
A classic hardness tester which is measuring the hardness by standard method of Brinell or Rockwell or Vickery or Shor and so on.
-
Product
Martindale Abrasion Tester
SG-P02M
-
This machine is ideal for determining the abrasion resistance of upper, lining, socking, and similar types of shoe materials, particularly those made of fabric. The specimens are capably tested for four bieces or six pieces(option) per time and are rubbed over the abrasive in all directions in a complex, repetitive pattern(a lissajous figure) and, at the same time, the holer totates.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Hardness Tester
NB3010 Series
-
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
Product
Heat Deflection Tester
-
Apparatus is used to determine the Heat Deflection Temperature or the Vi cat Softening Point. All the specimens are charged with a constant load and immersed in a bath, where temperature is increased at a standard velocity. The attained heat resistance rate of plastic materials is a widely required parameter for product characterization, for quality control, as well as for evaluating their conformity to the previewed applications.
-
Product
Insulation tester
-
The insulation resistance tester have these features with large LCD,backlight,holding data,Insulation resistance test with auto range,it has the construction of shakeproof ,dustproof ,damproof,and can be suitable for outdoor working environment,it apply to IEC 61010
-
Product
Damp-Heat Tester
-
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C；2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C；2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
Product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
-
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
Product
Earth Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
specially designed and manufactured for the field measurement of ground resistance, adopts digital and micro-processing technology, 3 wire or 2 wire method to measure ground resistance, with unique calibration function for wire resistance, anti-interference ability and environmental adaptability, to ensure the long-term measurement of high precision, high stability and reliability; The instrument out shell adopts waterproof protection case, anti-collision, anti-fall, waterproof (protection grade IP65),which is strong, safe and durable, the instrument is also equipped with large capacity rechargeable lithium battery pack, especially suitable for outdoor construction site to use.
-
Product
Continuity Testers
-
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
Product
Voltage/Continuity Tester
VOT-52
-
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
Product
Partial Discharge Tester
19501-K/19500
-
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
Product
Phase Testers
-
Measurement on the voltage detection terminal and covered wireSafely used even for high-voltage bare wiresConsisting of the transmission and reception parts as well as the optical fiber wire connection those two parts
-
Product
Downloadable PAT Tester
Apollo 500+
-
The Apollo 500+ features a comprehensive range of electrical safety tests with user configurable test sequences and checklists for PAT, PPM and PPE. It has storage for up to 10,000 test records and is compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
Product
ESD Tester
PurePulse
-
PurePulse is a flexible and efficient ESD tester for HBM, TLP, MM and HMM. Its 2-pin style setup reduces tester parasitics, it captures waveform data and can be automated to test thousands of pins without the need for a test fixture. Our PurePulse system was designed from the ground up to be customized to meet your testing needs, take a look at the features below and schedule a demo with us to learn more.
-
Product
Downloadable PAT Tester
Apollo 400+
-
The Apollo 400+ features a comprehensive range of electrical safety tests with user configurable test sequences and has storage for up to 2,000 test records. Compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
-
Product
Cable Tester
LX-560A
-
Shenzhen Lian Xin Technology Co., Ltd.
Cable/Harness Tester (low-pressure type) features its capability of testing the components inside the wire, the test speed more than double faster than that of the traditional wire testers, and the provision of such functions as unilateral, turn-on resistance editing, and spot metering color editing.
-
Product
Compact Semiconductor Tester
QST4416-FC
-
Qmax Test Technologies Pvt. Ltd.
The Qmax Model QST4416-FC is a compact small foot print, sophisticated automatic semiconductor tester. Its state-of-the-art hardware design which is freely configurable to user's application requirements and software features facilitates it to test linear & mixed signal IC components which covers a wide range of products like linear, Power management, Opto electronics, digital and mixed signal devices etc.
-
Product
Scorch Tester
-
TESTEX Testing Equipment Systems Ltd.
Scorch Tester, to determine fabrics Ironing color fastness and sublimation color fastness, and dimensional stability under hot dry conditions. Sublimation Fastness Tester complies with ISO 105, BS 1006, AATCC 92/114/117/133. Sublimation machine price is reasonable.
-
Product
Spray Rating Tester
TF160
-
TESTEX Testing Equipment Systems Ltd.
Spray Rating Tester, to determine the surface wetting resistance of fabrics, which may or may not have been given a water-resistant or water-repellent finish.
-
Product
Automatic Oil Tester
-
Theses tester sets are used for determining the di-electric BDV of insulating oils, both new and in-service from transformers, switchgear and other electrical equipments.
-
Product
Safety Tester
-
Safety analyzer is mainly used to provide the test solution for electric car, grid, photovoltaic, electrical appliances, information equipment, medical equipment industry as well as innovative solutions for the various electrical measurement.
-
Product
Environmental Testers
-
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
-
Product
Multi-Operational Surge Tester
M Model
-
Portable compact Multi-Operational Surge Tester that contains a multi-position carrying/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or field. The "M" is the perfect choice for your complete preventive/predictive maintenance testing - DC Hi-Pot testing, handheld resistance meter* testing and the capability of testing fully assembled grounded motors without rotating the rotor position.
