-
Product
Altitude Simulation Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
Product
Virtual Platform Development and Simulation
DEV
-
The Imperas Developer products consist of tools, models and infrastructure components critical for the high quality, rapid development and verification of embedded software, utilizing virtual platforms. The Developer products provide the necessary capabilities to develop platforms, including software simulation capability to execute embedded code on the platforms.
-
Product
The Imperas Instruction Set Simulator
ISS
-
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
Product
PXI RTD Simulator Module, 20 Channel, PT100
40-263-101
Simulator
The 40-263-101 is a 20-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
BRI, PRI and PSTN FXS Simulator
emutel Max
-
emutel Max is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Max can emulate different country specific networks by adding network personality cards " networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Max.
-
Product
MIMIC® JUNOS Simulator
-
MIMIC JUNOS Simulator fully supports Juniper JUNOS® software and SNMPv1, v2, v2c, v3. Up to 100,000 devices can be simulated in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. An extensible environment allows new MIBs and devices to be added to the simulation.
-
Product
Thermal-Mechanical Physical Simulation System
3180 System
-
Weld HAZ simulation. Melting and solidification. Heat treatmentHot tensile tests. CCT and CHT with deformation. Continuous casting simulation.
-
Product
IBP Simulator
IBPS 2.0
-
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
Product
Cyber Crisis Simulator
-
When responding to a cyber crisis, the C-Suite no longer works in a silo. Executive management continuously collaborates with incident response and SOC teams to make well-informed decisions. But tabletop exercises and conventional crisis simulation platforms do not prepare for this new reality.
-
Product
Close Match Solar Simulators
-
We design and manufacture a wide range of world leading solar simulators that meet and surpass the IEC, ASTM and JIS international standards. Our close spectral match solar simulators are used across the globe in world-leading laboratories. Our award winning Unisim solar simulators are used in both research and development work as well as 24/7 production facilities and are regularly cited in the latest photovoltaic research literature.
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
Modbus Slave Simulator
ModSim
-
ModSim32 is a very simple but powerful application for simulating data from modbus slave devices. ModSim is an MDI application which allows you to define multiple blocks of data points which may then be accessed from a connected modbus master.
-
Product
Capacitance Simulation Card
SET-1220
-
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
Product
Full System Simulator
Simics
-
Wind River Simics is a full system simulator used by software developers to simulate any target hardware from a single processor to large, complex, and connected electronic systems. This simulation enables the target software (board support package, firmware, real-time operating system, middleware, and application) to run on a virtual platform the same way it does on the physical hardware.
-
Product
PCI RTD Simulator Card 6-Channel PT100
50-262-101
Simulator
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
PCI Switch & Simulation Cards
-
Instrumentation grade PCI switch and simulation cards can be cascaded to form more extensive switching networks.
-
Product
Virtual Platform Simulation Acceleration
QuantumLeap
-
QuantumLeap is a parallel simulation performance accelerator that leverages a new synchronization algorithm to provide the fastest virtual platform software execution speed available. The execution performance of this new technology has been measured on average at 15 times faster than the nearest commercial solution using standard benchmarks.
-
Product
DIGITAL SATELLITE METER
1650S
-
The optimal satellite signal meter to test and measure both analog/digital signals(DVB-S, DSS). Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the satellite broadcasting signal.
-
Product
ARINC 429 Test And Simulation PCI Module
PCI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Automotive Supply Simulation System
-
Spitzenberger & Spies GmbH & Co. KG
The modularly constructed Automotive Supply Simulation System is a compact EMC-Test System for the execution of immunity measurements for pulse-shaped, line conducted disturbances at electronic equipment of motor vehicles. The high performance version enables tests of current-intense consumers or even complete vehicles
-
Product
Protocol Simulation
-
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
Product
Altitude Data Simulator
ADS-100
-
The Model ADS-100 is an all solid-state device that simulates the output of altitude encoders/digitizers in both parallel and serial (RS232) data formats. Designed to substitute for an altitude encoder when testing and troubleshooting an aircraft's altitude reporting system, the ADS-100 provides two RS-232 compliant outputs in addition to the ICAO pressure altitude code.
-
Product
Cycle Voltage Drop (Rise) Simulator
STT-CSS-20P1
-
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
Product
L Band Satellite over Fiber
-
Transport L Band signals from Satellite Dish to Receiver over Fiber Cable
-
Product
Electromagnetic Simulation Software Suite
EMTOOLS
-
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
