Link
See Also: Camera Link
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
-
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Carrier Card
PEX442
-
The PEX442 Mezzanine Carrier Card allows designers the flexibility to extend and expand the IO capability of their systems by supporting high bandwidth links to combinations of XMC, PMC and AFIX (Additional Flexible Interface Xtensions) modules using PCI Express infrastructure.
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
Heat Recovery Steam Generators
-
The heat recovery steam generator (HRSG) provides the thermodynamic link between the gas turbines and steam turbines in a combined-cycle power plant. Each HRSG solution is custom-engineered to meet your desired operating flexibility and performance requirements. With more than 750 HRSGs installed worldwide, GE is a world leader in supplying HRSGs behind all major OEM’s gas turbines.
-
Product
Low Profile PCI Express 8-Port
7803e
-
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Device Connectivity
-
The ability of electronic devices to link and exchange data with each other, users, or the internet using wired or wireless technologies, forming networks that enable functions like remote monitoring, automation, and seamless data sharing, crucial for the Internet of Things (IoT) and smart systems.
-
Product
Digital Fiber Multiplexers & Wavelength Shifters
FiberSaver Series
-
We don’t always have unlimited amounts of fiber at our disposal. Whether working in pre-fibered event venues, houses of worship or moving camera signals across busy metropolitan areas, fiber counts can quickly add up – especially when bi-directional optical transmission is required. MultiDyne’s FiberSaver Series is built for the system designer who needs a robust yet compact solution for signal links where fiber strands are limited, or where fiber feed requirements exceed budgets. FiberSaver products help technicians send and receive more optical signals over fewer fibers. Wavelength-agnostic inputs will multiplex just about any digital optical coming from SMPTE cameras, Network Switches, etc., and combine them with several optical matrix inputs. Scalable in increments of six channels, content producers now have a cost-effective solution to carry extra signals for sports production, distance learning and remote broadcasting.
-
Product
PXI 2A Multiplexer, 2-Bank, 8-Channel, 8-Pole
40-614C-013
-
This 2-bank, 8-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Purpose Built Network Packet Brokers
-
Garland Technology’s Purpose Built Network Packet Brokers (NPBs) are devices that provide access to network traffic from multiple links, helping to centralize and improve efficiencies by sharing packets between the monitoring and security appliances. Additional NPB features include filtering, aggregating, regenerating, and load balancing.
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-614D-010
-
The 40-614D-010 (PXI) and 42-614D-010 (PXIe) 2-bank, 64-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Premanaged Gigabit Ethernet Switch
XES-2T6
-
The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
-
Product
PXIe Chassis: High-Power, 18-slot, 24 GB/s
M9046A
-
The Keysight Technologies, Inc. M9046A PXIe 18-slot chassis delivers the power and cooling required for high-performance applications with 3 PXIe hybrid slots and Gen 3 backplane (maximum 24 GB/s system and 8 GB/s slot-to-slot) with a two-link (x8, x16) system slot and x8 links to the PXIe slots
-
Product
PXI/PXIe High Density 2A Multiplexer, 16-Bank, 4-Channel, 2-Pole
42-614D-002
-
The 40-614D-002 (PXI) and 42-614D-002 (PXIe) 16-bank, 4-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Digital VIS-SWIR Camera
OWL 1280
-
Using a 1280 x 1024 InGaAs sensor from SCD, the OwL 1280 offers visible extension from 0.6µm to 1.7µm to enable high sensitivity imaging. The 10µm x 10µm pixel pitch enables the highest resolution imaging. It will offer less than 28 electrons readout noise (rms) and with a high intra-scene dynamic range of 51dB, this enables simultaneous capture of bright & dark portions of a scene. Available with a 12 bit medium Camera Link digital output, the Owl 1280 will run from 10 to 60Hz. The camera features an on-board Automated Gain Control (AGC) which enables the best contrast image from low to bright light. The camera also has an on-board intelligent 3 point Non Uniform Correction (NUC) providing the highest quality images. As with all Raptor cameras, the Owl 1280 is ultra compact and rugged. The camera sensor temperature is stabilised to 15°C and the camera does not have a fan.
-
Product
PXI MUX 8 Banks of 8 Channel Screened 1 Pole
40-610-021-S-8/8/1
-
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Handheld Digital Multimeter, 4 ½ Digit, Basic
U1251B
-
50K counts DMM for electronics troubleshooting. Keysight Remote Link Solution enabled, which allows remote monitoring (wirelessly) on a mobile device.
-
Product
Serial Interfaces
-
All of ICS's Serial Interfaces provide GPIB like IEEE-488.2 functionality over an RS-232 or RS-485 Serial link and are serial devices.
-
Product
Telemetry Tensile Link
TL-3.0
-
The TL-3.0 is a third generation Telemetry Tensile Link load cell. A light weight wireless tension measuring unit that combines a high level of performance with a robust design for harsh environments.
-
Product
Optical Loss Test Set
OLTS
-
Tests for the total amount of light loss on a fiber optic link.
-
Product
Three Phase Closed I-P Link Energy Meter Test Bench Type KP-S3000-B
-
Bofa Instrument & Equipment Co., Ltd
Three phase closed I-P link energy meter test bench, type KP-S3000-B, is designed for testing three-phase energy meters, especially for testing Closed I-P Links three-phase energy meters. It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
8AI/11DI/10DO IoT Modbus/OPC UA Ethernet Remote I/O
ADAM-6317
-
OPC UA empowers Modbus I/O users to access the industrial IoT world.OPC UA I/O links SCADA and the cloud without the need for gateways, accelerating OT and IT convergence.Hardware and software double security levels to prevent being hacked.Cost-effective: high I/O density and daisy-chaining solution saves cost.
-
Product
Compact, Easy To Use Tester.
Eye-BERT 40G
-
The Eye-BERT 40G packs 40Gbps of test capability and a color touch screen into a compact, easy to use tester. The Eye-BERT 40G offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of QSFP transceivers as well as link verification and performance testing all in a single unit. The automated QSFP test feature also allows the user to quickly verify transceiver performance and automatically generate a report complete with unit serial number.
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 4-Channel, 16-Pole
42-614D-014
-
The 40-614D-014 (PXI) and 42-614D-014 (PXIe) 2-bank, 4-channel, 16-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
RF Solutions
-
ST offers wideband and multiband RF solutions for wireless communication infrastructure and RF equipment including GSM/3G/LTE base stations, microwave links, cable modems, satellite, broadcasting, instrumentation, security, defense and test equipment.
-
Product
Quartz ICP® Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load. The through-hole mounting supports platform, integrated link, and support style installations using either a through-bolt or the supplied stud.
-
Product
SFP
4 Gbps
-
Is specifically designed for high performance integrated duplex data link over multi mode optical fiber. The high-speed oxide VCSEL and photo diode are provided as a light source and a detector, respectively.
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 2 Amp, 250 Port
C500RMX-4SB-4B
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Tension Load Cells
-
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
Product
FireBird Camera Link Frame Grabber (2xCLD-2PE8)
AS-FBD-2XCLD-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
Variable Fiber Optic Attenuator
-
Variable fiber optic attenuator could help simulate distance or actual attenuation in the fiber optic testing work by inserting a calibrated attenuation into the link. By using the variable fiber optic attenuator, technicians could verify the power margin received by testing the fiber optic link power budget. Variable fiber attenuator can help user vary the light power injected from a light source into the optical fiber. Important parameter of variable fiber attenuator include its insertion loss, reflection loss and attenuation range.
