Programmable Voltage Sources
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
-
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 201kΩ
50-297-041
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 239Ω
40-252-013
-
The 40-252-013 is a programmable resistor module with 4 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-123-HI
-
The 40-230-123-HI (PXI) and 42-230-123-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 470Ω
40-298-014
-
The 40-298-014 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Precision Resistor Card 9-Channel, 1Ω To 122Ω
50-297-112
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-130-HI
-
The 40-230-130-HI (PXI) and 42-230-130-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module
782615-02
-
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-054
-
The 40-297A-054 (PXI) and the 42-297A-054 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-321-HI
-
The 40-230-321-HI (PXI) and 42-230-321-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 13.6kΩ
40-251-131
-
The 40-251-131 is a programmable resistor module with 2 channels which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-022
-
The 40-254-022 (PXI) and 42-254-022 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 239Ω
40-298-013
-
The 40-298-013 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-01
-
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 6.97kΩ
40-251-024
-
The 40-251-024 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 11.4MΩ
50-298-153
-
The 50-298-153 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-030
-
The 40-254-030 (PXI) and 42-254-030 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-252-011
-
The 40-252-011 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 122Ω
50-298-012
-
The 50-298-012 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe Source Measure Unit Family
PXS(e)840x
-
The PXS840x PXI SMU family is a high-speed, 4-quadrant source measure unit. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-023
-
The 40-254-023 (PXI) and 42-254-023 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 3.55Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-053
-
The 40-297A-053 (PXI) and the 42-297A-053 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-125
-
The 40-297A-125 (PXI) and the 42-297A-125 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-116
-
The 40-254-116 (PXI) and 42-254-116 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 1.8kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-115
-
The 40-297A-115 (PXI) and the 42-297A-115 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 920 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
