Couplers
enable a signal to be used in another circuit.
-
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Additional Components
-
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
Product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
Voltage Input Module
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
Product
PD Calibrator
-
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
Product
Coupler Metrology
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger provides directional coupler-based measurement techniques as well as probes for comprehensive cross-domain coupling analysis.Nowadays, the introduction of new accessories within vehicles, like rear seat infotainment, smart dashboards, and various advanced driver assistance systems, has increased the demand for high-speed automotive bus systems working in parallel with the high-voltage power networks in electric cars.
-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
30 DB Directional Couplers From 0.5 To 40 GHz
-
Pulsar Microwave's CS30 series single directional couplers operate at narrow and wideband frequencies within 500 MHz to 40 GHz. They have a nominal coupling value of 30 dB, with tolerances of +/- 1 to 1.25 dB. These directional couplers are rated at 50 watts maximum input power. These couplers are optimized for best matching and high directivity with flat coupling response. They come standard with SMA or N female connectors.
-
Product
Multi Current-Mode-Coupler
Sy629PMC-M-CMC
-
The Sy629PMC-M-CMC module allows ARINC-629 terminals to communicate directly without the need for an ARINC-629 bus Cable and conventional Current Mode Couplers.
-
Product
Dual Directional Couplers From 0.5 To 40 GHz
-
Dual directional couplers from Pulsar Microwave are available in standard values of 10, 20 and 30 dB with coupling tolerance of +/- 1.25 dB. They are available in narrowband and wideband designs from 500 MHz to 40 GHz. Most models have a coupling flatness of +/- 0.8 dB. Input Power is rated for 50 watts.
-
-
Product
Utility Module
FTBx-9600
-
1x2 to 1x8 couplers. Various coupling ratios to fit the application. Protected component to avoid breaking or damaging. Available with EI or EA connectors, and compatible with EXFO’s Universal Interface (EUI).
-
Product
Coupler Workstations
-
Workstations using pure hydrogen gas from a tabletop generator, tank supply, or oxygen, can achieve high enough temperatures to develop Fused Biconic Tapered devices, Power Combiners, Wavelength Division Multiplexers, Thermal Core Expansion devices, and many other products.
-
Product
For accurate testing of headphones, microphones telephones and loudspeakers
Artificial Mouths, Ears, and Couplers
-
Listen supplies artificial mouths, ears and ear couplers from Brüel and Kjær, GRAS and more.
-
Product
6-8 DB Directional Couplers From 0.5 To 40 GHz
-
Pulsar Microwave manufactures the CS06 and CS08 series single directional couplers in nominal values of 6 and 8 dB, respectively. These directional couplers are used in 50-ohm systems for narrow and wideband applications within 500 MHz to 40 GHz. Standard outlines are fitted with SMA or N type female connectors, but Pulsar Microwave can customize upon request.
-
Product
Pump Combiners
-
Pump combiners, also called pump couplers, are special application fiberoptic couplers used for sending pump and signal light into an amplifier or laser fiber. Because of these applications, pump combiners are specially designed for high-power use.
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
Pathfinder Locating System
The STICK™
-
Built with Pathfinder SAF Technology™ at its core, the Stick offers RYCOM’s most ophisticated technology in an economical package. Pathfinder SAF Technology™ is the heart of our premium locators, now RYCOM is applying this proven technology throughout the entire product line. From crowded easements, to long runs of pipe, to the most demanding of locating environments, users can depend on The Stick. Dependability is not only driven by the internal technology, but The Stick is built to last with an aluminum housing and sealed against weather. The ruggedly designed and well balanced receiver includes an LCD screen providing relative and actual signal strength, as well as a speaker for variable audio pitch. A peaking signal response allows the user to minimize interference and maintain the locate on the target conductor. The Stick cable and pipe locator offers multiple active frequencies — from 50Hz to 82kHz — ensuring flexibility to match the needs of the most complicated locating environments. Transmitter functions include transmitter induction, coupler induction and direct connection. Whether the locate is measured in feet or miles, with automatic impedance matching from 5 ohm to 25,000 ohms and 3 watts of output power, The Stick will meet the challenge. Rycom Instruments®, Inc. locators are designed and manufactured to make utility locating as accurate as you need and as simple as you want.
-
Product
1553 to Ethernet Converter
eNet-1553
Ethernet Interface
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
Product
Digital Module For Remote I/O
ITA
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
RF Components
-
Our Components product line consists of standard RF components and unique designs for custom microwave applications. We provide rugged, reliable and quality solutions for low and high power attenuation, termination, coupler, and power-divider applications. In addition to our extensive line of standard products, Bird has a reputation for designing custom solutions for custom applications. Bird has done hundreds of special versions of RF components to meet the unique needs of our customers. Common requests for customization include: Special Connectors, Non-Standard Attenuation Values, Mismatch Loads, Exceptional Peak or Average Power Handling Capability, Extremely Low VSWR Requirements, Custom Test Requirements and many others!
-
Product
90 Degree Hybrid Couplers To 600 MHz
-
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
-
Product
Isolation Amplifier Analog Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
IPD RF Components – LTCC
-
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
Product
Octocouplers
-
Panasonic Industrial Devices Sales Company of America
Panasonic's PhotoIC Coupler is a high performance optocoupler which consists of LED in input circuit, and custom IC in output circuits. PhotoIC Couplers are commonly used for high speed communication requiring physical isolation in various equipment and devices.
-
Product
RF Calibration Kit
SMK-3000
-
The SMK calibration kits are precision, high power calibration standards that are used to calibrate RF radios, wattmeters, directional couplers and other high-power RF test equipment in the field or metrology lab. Unlike other calibration solutions, the SMK-3000 calibration kits reduce the cost of ownership and provide a much faster time-to-calibration with lab precision and accuracy you’ve come to expect from Bird.
-
Product
CXM Custom Chassis
Chassis
Cytec can manufacture custom microwave systems to your specifications. Need to build a switch with 6 different styles of relays? Want to combine relays, amps, splitters and couplers? Need to combine parts from 8 different vendors to meet the specs you want?
-
Product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
Digital Module
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
Product
IPM Drive
-
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
Product
High-Speed CMOS Output
-
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
